O.S. engine MAX FXi 46 Скачать руководство пользователя | Manualshive

Страница: 7 / 28

background image

This range of engines is ideally suited to a
variety of R/C aircraft, including trainer,
sports, acrobatic and scale types.

A separate precision-made needle-valve
unit is installed at the rear, where manual
adjustment is safely remote from the
rotating propeller.

Common Accessories
No. 8 Glow Plug, Silicone Tube, Instruction
Manual.

Note: With these engines, the piston will
feel tight at the top of its stroke when the
engine is cold. This is normal. The piston
and cylinder are designed to achieve a
perfect running clearance when they
reach their intended running temperature.

Installing the Glow Plug
Carefully insert plug, with washer, finger
tight only, before final tightening with the
correct size plug wrench.

Connecting the Fuel Tubing
Connect the short length of fuel tubing
(supplied) securely between the needle-
valve outlet and carburetor inlet as shown in
the illustration on the next page.

In the event of the tubing becoming
damaged, it should be replaced with a
suitable length (as indicated below) of best
quality 5mm OD x 2mm ID silicone tubing.
Use similar material to connect the fuel inlet
nipple to the fuel tank.

BEFORE INSTALLING THE ENGINE

FEATURES OF FXi SERIES ENGINE

7

«
...
5
6
7
8
9
...
»

Содержание MAX FXi 46





























Отзывы:

Нет отзывов

Похожие инструкции для MAX FXi 46

Бренд: VEM Страницы: 27

Бренд: D+H Страницы: 20

MerCruiser Diesel Inboard 2.8L

Бренд: Mercury Страницы: 93

Бренд: Great Wall Страницы: 72

Бренд: Tanaka Страницы: 11

Бренд: MTHTrains Страницы: 20

Бренд: Robin America Страницы: 24

Бренд: Coleman Страницы: 24

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

B21 ADAM DRAKE EDITION

Бренд: O.S. Speed Страницы: 4

Бренд: Rockwell Automation Страницы: 28

Бренд: IBS Страницы: 8

Бренд: Team Biland Страницы: 18

Бренд: Yanmar Страницы: 263

Бренд: Thermador Страницы: 20

Бренд: Thermador Страницы: 20

Бренд: Wood-mizer Страницы: 192

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды