NXP Semiconductors QorIQ LS1028A Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 112

NXP Semiconductors QorIQ LS1028A Скачать руководство пользователя страница 27

Table 7. SerDes assignments

SerDes
module

Lane

Connectivity

Port

1

0 / A

Qualcomm AR8033 1 GbE PHY

1 x 1GbE RJ45 on SGMII MAC interface

1 / B

NXP F104S8A QSGMII

Quad 1 GbE PHY

4 x 1GbE RJ45 on QSGMII MAC interface

2 / C

PCIe Gen 3 (8 Gbit/s)

M.2 Key E slot for Wi-Fi cards

3 / D

PCIe Gen 3 (8 Gbit/s)

or

SATA 3.0 (6 Gbit/s)

M.2 Key E slot for Wi-Fi cards

or

M.2 Key B slot for SATA based SSD cards

2.8 Ethernet controller interface

The LS1028A processor supports one Ethernet controller (ENETC), which connects either to an onboard 1588 access header or
to an audio transceiver (through TX signals only) and an SGMII port (over LYNX36 SerDes Lane A). The controller also supports
QSGMII connectivity through the TSN switch and it is available over LYNX36 SerDes interface (Lane B).

The EMI1 MDIO/MDC signals control the SGMII and QSGMII PHY transceivers. EMI1 operates at OVDD (1.8 V) levels. The
signals are bi-directionally shifted to 2.5 V for compatibility with both AR8033 (one-port SGMII) and F104S8A PHY (Four-port
QSGMII).

2.8.1 SGMII Ethernet

The onboard Ethernet PHY, Qualcomm AR8033 PHY (U23) connects to the ENETC of the LS1028A processor using SGMII
protocol over LYNX36 SerDes lane A.

Ethernet controller interface

QorIQ LS1028A Reference Design Board Reference Manual, Rev. b, 11/2018

NXP Semiconductors

COMPANY CONFIDENTIAL

27

«
...
25
26
27
28
29
...
»

Содержание QorIQ LS1028A

















































































































Отзывы:

Нет отзывов