NXP Semiconductors LS1046ARDB Скачать руководство пользователя страница 47

Страница: 47 / 64

Table continued from the previous page...

Field

Function

SD1REFCLK_S

EL_EN

SD1REFCLK_SEL_EN

SerDes1 reference clock 2 control register enable

0b: REG_SD1REFCLK_SEL Register no effect (default value)

1b: REG_SD1REFCLK_SEL Register take effect

EC2_SEL_EN

Ethernet controller 2 connection control register enable

0b: REG_RGMII_1588_SEL Register no effect (default value)

1b: REG_RGMII_1588_SEL Register take effect

1588_CLK_EN

1588 interface clock source control enable

0b: REG_1588_CLK_SEL Register no effect (default value)

1b: REG_1588_CLK_SEL Register take effect

QSPI_BANK_E

QSPI_BANK_EN

QSPI flash bank setting register enable

0b: REG_QSPI_Bank Register no effect (default value)

1b: REG_QSPI_Bank Register take effect

SD_EMMC_EN

SD or EMMC interface control register enable

0b: REG_SD_EMMC Register no effect (default value)

1b: REG_SD_EMMC Register take effect

3.6 RCW Source Location POR Register 1 (REG_CFG_RCW_

SRC1)

Offset

Register

Offset

REG_CFG_RCW_SRC1 5h

Function
Use this register to configure RCW source POR bits 0-7.

RCW Source Location POR Register 1 (REG_CFG_RCW_SRC1)

QorIQ LS1046A Reference Design Board Reference Manual, Rev. 2, 30 May 2019

NXP Semiconductors

Содержание LS1046ARDB

































































Результаты поиска

Содержание LS1046ARDB

Отзывы:

NXP Semiconductors LS1046ARDB, Справочное руководство, Страница: 47 / 64

Результаты поиска

Содержание LS1046ARDB

Отзывы: