manualshive.com logo in svg

NXP Semiconductors LS1046ARDB, Справочное руководство, Страница: 13 / 64

Поделиться
Скачать
NXP Semiconductors LS1046ARDB Скачать руководство пользователя страница 13

Table 3. LS1046ARDB features (continued)

Board feature

Processor feature used

Description

Clocks

25 MHz crystal:

• Provides 25 MHz input to the clock generator

(6V49205BNLGI)

SYSCLK:

• Supports single-ended SYSCLK and DDRCLK clock

input (default value = 100 MHz)

• Supports single-source differential DIFF_SYCLK (default

value = 100 MHz)

SerDes:

• Provides clocks to all SerDes blocks and slots

• 100 MHz for SD1_REF_CLK1

• 100 MHz or 156.25 MHz for SD1_REF_CLK2

• 100 MHz for SD1_REF_CLK1 and SD1_REF_CLK2

• 100 MHz for MPCIE_CLK and PCIE_CLK

RTC:

• Supports 32.768 kHz for RTC

Ethernet:

• Provides option for 25 MHz clock output (CLKOUT) from

clock generator to Ethernet RGMII and SGMII
transceivers

• Supports 100 MHz XGT1588_CLK and 50 MHz to 10G

PHY AQR106/107

CPLD:

• Supports 32.768 kHz for PLD_CLK

SFP:

• Supports 25 MHz for XFI1_REFCLK

System logic (CPLD)

• Supports a CPLD with 8-bit registers

• Manages system power and reset sequencing

• Controls POR settings

• Controls signal muxing/demuxing

• Latches IFC address/data multiplexed signals

DIP switches

• Three DIP switches for quick board configuration

 

See 

QorIQ LS1046A Reference Design

Board Getting Started Guide

 for more

details on LS1046ARDB DIP switches.

  NOTE  

Table continues on the next page...

Board features

QorIQ LS1046A Reference Design Board Reference Manual, Rev. 2, 30 May 2019

NXP Semiconductors

13

Содержание LS1046ARDB

































































Отзывы:

Нет отзывов