Nussbaum MCS 5500 ND WIRELESS Скачать руководство пользователя страница 4

Страница: 4 / 57

Operating Instruction and Documentation

MCS 5500 ND WIRELESS

- 4 -

As far as required and ordered by regulations personal protective equipment is to be

used

All safety- and danger-hints at the lift are to be observed!

Spare parts must comply with technical requirements laid down by the manufacturer.

This is only warranted with original parts.

Consider time intervals given or fixed in instructions for use for repeated

tests/inspections.

Maintenanceworks, remedy of faults and disposal

Fixed Adjusting-, maintenance- and inspectionworks and time intervals including

Details for exchange of parts/part components as mentioned in the instructions for use are to be

adhered.

These works must only be carried out by expert personal.

After maintenance- and repair works loose screw connections must always be firmly

tightend!

Guarantee and liability

Our „General conditions of selling and delivering“ are in force.

There will be no guarantee or liability for injuries of persons or things if these injuries are caused

by one or by some of the following reasons.

Inappropriate use of the lift.

Inappropriate installation, initiation, operation and maintenance of the lift.

Use of the lift while one or several security devices do not work or do not work

correctly or are not installed correctly.

Not to follow the regulations of the operating instruction concerning transport, storing,

installation, initiation, operation and maintenance of the lift.

Changes of the construction of the lift without asking the producer.

Changes of important adjustments of the lift (e.g. driving elements, power rating, motor speed,

etc)

Wrong or incorrect maintenance.

Catastrophes, acts of God or external reasons.

Содержание MCS 5500 ND WIRELESS


























































Результаты поиска

Содержание MCS 5500 ND WIRELESS

Отзывы:

Похожие инструкции для MCS 5500 ND WIRELESS

Бренды по названию

Популярные бренды

Nussbaum MCS 5500 ND WIRELESS, Руководство по эксплуатации

Результаты поиска

Содержание MCS 5500 ND WIRELESS

Отзывы:

Похожие инструкции для MCS 5500 ND WIRELESS

Бренды по названию

Популярные бренды