manualshive.com logo in svg

Nussbaum MCS 5500 ND WIRELESS, Руководство по эксплуатации, Страница: 25 / 57

Поделиться
Скачать
Nussbaum MCS 5500 ND WIRELESS Скачать руководство пользователя страница 25

 Operating Instruction and Documentation 

                                                                                             

MCS 5500 ND WIRELESS 

 

- 25 - 

  

 

Pic 8:  
Loosen the cap of the Minimess connection and the cap 
of the tank. Fasten the Minimess hydraulic tube at the 
screw fitting and put the other end into the tank. 

 

 

 

 

 
 
 
 

 

Pic 9: 
Use the long screw thread-bushing and turns with a suitable 
tool (key-wideness 24, available with your dealer,), clockwise. 
Lower the lifting carriage  only approx. 5cm – 10 cm. Repeat 
the process at the next column. Lower always 5 cm-10 cm 
until all lift are in the lowest position. 
Repair the defective lift. After it create a Reset which is 
described in the operating instruction.

 

 

Attention!! 

Lower the automotive-lift only approx. 

5cm – 10 cm.

 

 

 Observe the complete emergency lowering process.  

 

Do not work with the lift until the defective parts are changed. 

 

You can only work again with the automotive-lift, if it is in a safety-related perfect 
condition.

 

 

 

•  After it, carry out an reset as described in the operating instruction.

 

 

Содержание MCS 5500 ND WIRELESS


























































Отзывы:

Нет отзывов