Nussbaum MCS 5500 ND WIRELESS Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 57

background image

Operating Instruction and Documentation

MCS 5500 ND WIRELESS

- 17 -

• Observe the position of the wheels in the mobile column lift

(see pic. 6 and 7).

Before lifting the load, lower the mobile-column-lift in the lowest position (remove the
shaft), otherwise a malfunction can lead it to damages.

• Connect or disconnect the columns (observe the sketch) only if the main switch is

switched off. Otherwise a malfunction can be occur.

• Check the dangerous places of the lift and be sure that there are no objects or people in

the immediate area of the lift or on the lift.

• Switch on the control system; Switch-on the main switch on position ”1” .
• Raise the vehicle. Use all columns. Press the buttons „1-4”, at the operating unit.

If the column is active, the switches of the chosen columns, are lighten.

•  Lift the vehicle on the working height. Press the button „lifting“ .
•  In the display of the operating unit you can read the momentary height of the supports.
•  Observe the complete process.

It is only allowed to lift or to lower the column lift with load. Otherwise a column lift
without load can cause an unequal. After it, this column lift switch-off the complete
system.
Accordingly, the number of the lifting wheels must agree with the number of the

column lift. Please, switch off the column, which do you not need.

wrong

Correct

pic. 6

pic. 7

«
...
15
16
17
18
19
...
»

Содержание MCS 5500 ND WIRELESS


























































Отзывы:

Нет отзывов

Похожие инструкции для MCS 5500 ND WIRELESS

Бренд: Valx Страницы: 28

Бренд: Global Lift Страницы: 51

Бренд: Rotary Страницы: 30

Бренд: Huchez Страницы: 15

Бренд: WITTUR Страницы: 47

Бренд: morse Страницы: 8

Panellift Hangpro 150

Бренд: Paragon Pro Страницы: 16

Бренд: Ravaglioli Страницы: 38

Бренд: rav Страницы: 88

Бренд: Ravaglioli Страницы: 162

Бренд: Hy-Brid Lifts Страницы: 24

Бренд: Hy-Brid Lifts Страницы: 28

Бренд: Hy-Brid Lifts Страницы: 36

Бренд: MAHA Страницы: 15

Бренд: rav Страницы: 84

Бренд: Omega Страницы: 8

Бренд: Ravaglioli Страницы: 80

Бренд: Ravaglioli Страницы: 82

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды