Nugen Nugen S150PS Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 39

background image

OPERATOR & MAINTENANCE MANUAL

25

5.2.2 Fuel

Remove the fuel inlet cap and check the fuel level in the
tank.



Adding fuel



Select the correct fuel.



Loosen the fuel inlet cap and remove it.



Fill the fuel through the inlet until the fuel is slightly less than the full tank level.



Tighten the fuel inlet cap.

Caution:

Do not smoke while you are refuelling an engine. Do not refuel an engine near open
flames or sparks. Always stop the engine before refuelling.

5.2.3 Coolant

Remove the coolant inlet and radiator caps,

check the coolant level in the tank.



Adding coolant



Remove the coolant inlet cap.



Remove the radiator cap.



Fill coolant to the radiator inlet top.



Reinstall and tighten the coolant inlet and radiator
caps.

Warning:

Avoid injury!    The radiator will be hot and can burn skin.    Built-up pressure may cause
explosive  release  of  coolant  when  the  radiator  cap  is  removed.    Shut  off  engine  and
allow  to  cool.    Do  not  remove  the  cap  unless  the  radiator  and  the  engine  are  cool  to
touch with bare hands.    Slowly loosen the cap to the first stop to release all pressure.
Then remove cap.

«
...
24
25
26
27
28
...
»

Содержание Nugen S150PS








































Отзывы:

Нет отзывов

Похожие инструкции для Nugen S150PS

Бренд: 3onedata Страницы: 3

Бренд: EAST COAST Страницы: 10

SignalPilot 51840

Бренд: Esu Страницы: 32

Varispeed CIMR-G7A

Бренд: YASKAWA Страницы: 459

Бренд: BK Precision Страницы: 23

Sync Converter/Stabilizer SCS 300

Бренд: Extron electronics Страницы: 1

Бренд: EBARA Страницы: 34

DASNET-SPLITTER

Бренд: D.A.S. Страницы: 12

Бренд: Digitus Страницы: 6

Бренд: SIIG Страницы: 12

Бренд: IONODES Страницы: 23

Бренд: Zamp Solar Страницы: 7

Бренд: Viking Страницы: 6

STEVAL-CTM004V1

Бренд: STMicroelectronics Страницы: 40

Бренд: Rohde & Schwarz Страницы: 653

HYT-10.0HV-EUG1

Бренд: Hoymiles Страницы: 34

Hubner Berlin POG 86

Бренд: Baumer Страницы: 36

Бренд: wagner solar Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды