NSK MEGATORQUE MOTOR SYSTEM Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 44

background image

Limited Warranty

NSK Ltd. warrants its products to be free from defects in material and/or workmanship which NSK
Ltd. is notified of in writing within, which comes first, one (1) year of shipment or 2400 total
operation hours. NSK Ltd., at its option, and with transportation charges prepaid by the claimant,
will repair or replace any product which has been proved to the satisfaction of NSK Ltd. to have a
defect in material and/or workmanship.

This warranty is the sole and exclusive remedy available, and under no circumstances shall NSK
Ltd. be liable for any consequential damages, loss of profits and/or personal injury as a result of
claim arising under this limited warranty. NSK Ltd. makes no other warranty express or implied,
and disclaims any warranties for fitness for a particular purpose or merchantability.

Copyright 2011 by NSK Ltd., Tokyo, Japan

All rights reserved.

No part of this publication may be reproduced in any
form or by any means without permission in writing
from NSK Ltd.

NSK Ltd. reserves the right to make changes to any
products herein to improve reliability, function or design
without prior notice and without any obligation.

NSK Ltd. does not assume any liability arising out of the
application or use of any product described herein;
neither does it convey any license under its present
patent nor the rights of others.

Patents issued and patents pending.

“MEGATORQUE” is a registered trademark of NSK Ltd. in
Japan and that of NSK Corp. in the United States of
America.

«
1
2
3
4
...
»

Содержание MEGATORQUE MOTOR SYSTEM













































Отзывы:

Нет отзывов

Похожие инструкции для MEGATORQUE MOTOR SYSTEM

Бренд: Eaton Страницы: 24

Бренд: Perkins Страницы: 112

Бренд: Vimar Страницы: 16

Бренд: Himax Страницы: 2

Бренд: Westerbeke Страницы: 64

Бренд: Honda Страницы: 69

Бренд: Honda Страницы: 97

Бренд: Honda Страницы: 48

Бренд: Honda Страницы: 156

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: LONCIN Страницы: 224

Бренд: Barrus Страницы: 59

G18 LT20 Series

Бренд: Wood-mizer Страницы: 22

PS01-48x240F-EX-E

Бренд: LinMot Страницы: 52

Бренд: Tecno Automazione Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды