manualshive.com logo in svg

Novus 500, Руководство оператора

Поделиться
Скачать
Novus 500 Скачать руководство пользователя страница 20

16

Installation

2.4 Wiring the UPS

DANGER: Before starting, make sure line power is turned off and that the UPS’s 

battery and input circuit breakers are turned off.
If stranded wires are used for the input and output terminal blocks, ferules MUST 

be used.

Tools and Materials Required

•  Slot head screwdriver to fit the terminal blocks.

•  Maximum 12 AWG copper wire rated to at least 90°C for the input and output power 

terminal blocks (or as specified by the local electrical code).

Procedure

1.  Connect the battery temperature sensor 

to the UPS. Attach the sensor end of the 

cable to the side of the centre battery as 

shown in Figure 2.3.1.

2.  If used, connect:

• The Ethernet port. 
• The RS-232 port.
• The dry contacts.
• The user inputs.

3.  Connect the load line to the UPS’s output 

terminal block.

4.  Connect the line power line to the UPS’s 

input terminal block.

DANGER: Before proceeding,  

verify the line wire is attached to 

the line terminal block, the ground 

wire is attached to the ground 

terminal block and the neutral wire 

is attached to the neutral terminal 

block to prevent accidental shocks 

or electrocutions.

5.  Connect the external battery.

Wiring Finished

Содержание 500





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды