NovaTec VL Series Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 22

background image

© NOVATEC, Inc. 2013 All Rights Reserved

VL-VLP IM 4-12-2013

6

NOVATEC VLP Series vacuum loaders operate in a similar manner

to the VL’s, but are designed

to convey free flowing powders.

4- VLP SPECIFICATIONS

Options:
Additional tubing and fittings (Rigid tubing, elbows, bolted couplers, etc.)
Alternate sight glass sizes are available for most Machine Mount models.
220/1/50-60 Volt Power
Brushless motor for VLP-38
Accessories:

asVR-MM-8

asVR-MM-12

asVR-MM-16

8 lb. Sight Glass Conversion Kit

12 lb. Sight Glass Conversion Kit

16 lb. Sight Glass Conversion Kit

Conversion Kit to increase sight glass capacity for
VL & VLP-12 and -19 models. Includes base, borosilicate
glass, top adapter plate and discharge valve.

«
...
4
5
6
7
8
...
»

Содержание VL Series























Отзывы:

Нет отзывов

Похожие инструкции для VL Series

Бренд: b-mola Страницы: 9

Бренд: Jet Страницы: 14

Бренд: Kärcher Страницы: 176

Бренд: Kärcher Страницы: 18

Бренд: Parkside Страницы: 36

Бренд: Parkside Страницы: 42

Бренд: Kärcher Страницы: 15

Бренд: COOLFORT Страницы: 20

Бренд: Home Comfort Страницы: 123

Бренд: Fanset Страницы: 16

Бренд: Eureka Страницы: 8

Бренд: ulsonix Страницы: 21

Бренд: Gorenje Страницы: 26

Бренд: Flexit Страницы: 76

Бренд: Bissell Страницы: 8

Бренд: Westinghouse Страницы: 64

Бренд: COMAC Страницы: 16

PROHEAT 2X 66Q4

Бренд: Bissell Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды