NovaTec VL Series Скачать руководство пользователя страница 3

Страница: 3 / 22

VL-VLP IM 4-12-2013

Table of Contents

1-PRINCIPLE OF OPERATION ...................................................................................................... 4

2-UNPACKING AND INSPECTION ................................................................................................ 4

3-VL SPECIFICATIONS .................................................................................................................. 5

4-VLP SPECIFICATIONS ............................................................................................................... 6

5-LOADER INSTALLATION ........................................................................................................... 7

5.1 CONTROL INSTALLATION

.............................................................................................................. 7

6-OPERATION OVERVIEW ........................................................................................................... 8

7-NO-LOAD ALARM FEATURE ...................................................................................................... 8

8-ADJUSTING the LOADER CONTROL ........................................................................................ 9

8.1 TO CHANGE LOADING PARAMETERS

........................................................................................ 9

8.2 PARAMETERS EXPLANATION

....................................................................................................... 9

9-INITIAL START UP .................................................................................................................... 11

9.1 CONVEYING NOTES

....................................................................................................................... 11

10-MAINTENANCE ....................................................................................................................... 12

10.1- VL Series - FLAT FILTER CLEANING:

...................................................................................... 12

10.2- VLP Series - CARTRIDGE FILTER CLEANING:

..................................................................... 13

10.3- VACUUM MOTOR BRUSH REPLACEMENT

........................................................................... 14

10.4- VL-12 through VL-38 and VLP-12 through VLP-38 MOTOR BRUSH REPLACEMENT

.. 15

10.5- VL-5, VLP-5 MOTOR BRUSH REPLACEMENT

...................................................................... 15

10.6- MOTOR REPLACEMENT

............................................................................................................ 16

11-TROUBLESHOOTING ............................................................................................................. 17

12-WARRANTY

– NOVATEC, INC. - Effective Date 6-12-2012 ................................................... 18

13- ELECTRICAL DRAWINGS ..................................................................................................... 19

14-VL SERIES LOADER PARTS LIST ......................................................................................... 21

15-VLP SERIES LOADERS PARTS LIST .................................................................................... 22

Содержание VL Series





















Результаты поиска

Содержание VL Series

Отзывы:

Похожие инструкции для VL Series

Бренды по названию

Популярные бренды

NovaTec VL Series, Инструкция по эксплуатации

Результаты поиска

Содержание VL Series

Отзывы:

Похожие инструкции для VL Series

Бренды по названию

Популярные бренды