NorthStar 8000I Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 220

NorthStar 8000I Скачать руководство пользователя страница 93

Northstar 8000i Operation Manual

93

13

Introduction to 3D Chart

3D Chart information is supplied by C-Map. You can use 3D Chart to see a
panoramic view of the selected area, as if you were flying over it. You can change
your elevation and the angle of view, and zoom in and out to show more or less
detail. You can also choose whether or not to show the seabed.

If you display the

Chart

screen and the

3D Chart

screen side-by-side in two panes,

you can synchronize the two panes to show different perspectives of the same
area.

3D Chart requires position data if you want to show your vessel position in real-
time on the

3D Chart

screen.

Note that the level of detail in 3D Chart, and the availability of satellite photos or
aerial photos to overlay on land areas depend on your geographical location.
Areas around the USA usually have the best level of detail.

13.1

Display the 3D Chart screen

To display the 3D Chart screen:

1. Select

Display

, then select

3D Char

t. (Alternatively, select a Page

that contains the 3D Chart in one of the panes.)

2. The

3D Chart

screen is displayed. See the following sections for

information about using the 3D Chart screen.

3. If position data is available, the 8000i acquires your vessel's position

then displays the local area as a

3D Chart

screen with your vessel

shown on it, and the

3D Chart

control panel on the right hand side of

your screen.

13.2

Reposition the 3D Chart screen to show your vessel

If your vessel isn't shown on the

3D Chart

screen, the

Show Vessel

button is

toggled Off or you're viewing part of the 3D Chart screen that doesn't include your
vessel.

To show your vessel on the 3D Chart screen:

1. Select:

the

Vessel

key or

Show Vessel

if you can see this button in the control panel

2. The 8000i repositions the

3D Chart

screen to show your vessel in the

center of the lower half of the

3D Chart

screen and the view will rotate

around this position.

3. The

Show Vessel

button is automatically toggled On.

«
...
91
92
93
94
95
...
»

Содержание 8000I





























































































































































































































Отзывы:

Нет отзывов