Nortel Passport 8600 Series Скачать руководство пользователя страница 75

Страница: 75 / 164

SF/CPU modules

The following table describes the 8692 SF/CPU module LEDs.

Table 27
8692 SF/CPU module LEDs

Label

Color, State

Meaning

Green

The module completed software initialization
and is operating normally.

Off

The module is not installed or did not initialize
properly.

Green, Steady

The management port is connected and linked.

Link

Off

There is no link to the management port.

Green, Steady

The management port is operating at 100 Mbps.

100

Off

The management port is operating at 10 Mbps.

Switch Utilization (8 LEDs)

Green

The number of lit LEDs indicates the utilization
level (full-duplex operation) of the switch fabric
as follows:

1 LED = 4.0 Gbps to 34 Gbps

2 LEDs = 34 Gbps to 68 Gbps

3 LEDs = 68 Gbps to 102 Gbps

4 LEDs = 102 Gbps to 136 Gbps

5 LEDs = 136 Gbps to 170 Gbps

6 LEDs = 170 Gbps to 204 Gbps

7 LEDs = 204 Gbps to 238 Gbps

8 LEDs = 238 Gbps to 256 Gbps

The number of lit LEDs indicates the level of
CPU activity (full-duplex operation) as follows:

1 LED = 12%

5 LEDs = 60%

2 LEDs = 24%

6 LEDs = 72%

3 LEDs = 36%

7 LEDs = 84%

CPU Utilization
(8 LEDs)

Green

4 LEDs = 48%

8 LEDs = 100%

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Содержание Passport 8600 Series
































































































































































Результаты поиска

Содержание Passport 8600 Series

Отзывы:

Nortel Passport 8600 Series, Руководство по установке, Страница: 75 / 164

Результаты поиска

Содержание Passport 8600 Series

Отзывы: