manualshive.com logo in svg

Nortel Passport 8600 Series, Руководство по установке, Страница: 145 / 164

Поделиться
Скачать
Nortel Passport 8600 Series Скачать руководство пользователя страница 145

8692 SF/CPU module

145

8692 SF/CPU Console port

The Console serial port is implemented as a DB-9 connector. This port
can operate as a data terminal equipment (DTE) or data communication
equipment (DCE) device. Use the switch to the left of the port to set the
port to DTE (right) or DCE (left). Default settings for this port are 9600
bits/s, 8 data bits, no parity, and one stop bit.

Connection to TXD and RXD signals and GND is sufficient for the console
serial port to fully function. The Console port does not support inbound
flow control; that is, the port does not toggle control lines to indicate an
input buffer full condition.

The following table lists the pin assignments for the Console port for both
the DTE and DCE settings.

Table 91
Pin assignments: 8692 SF/CPU module Console port

Switch position

Connector

Pin number

DCE (left)

DTE right)

2

TXD (Output)

RXD (Input)

3

RXD (Input)

TXD (Output)

4

DSR (Input)

DTR (Output)

5

GND

GND

6

DTR (Output)

DSR (Input)

7

CTS (Input)

RTS (Output)

8

RTS (Output)

CTS (Input)

8692 SF/CPU modem port

The Modem serial port is implemented on a DB-9 connector wired as a
DTE connection.

To set up modem access, you need a DTE-to-DCE cable ( straight or
transmit cable) between the Modem port and a modem or terminal server.

The following table describes the required cable pin assignments.

Table 92
Pin assignments: DTE to DCE

Switch

Modem

Signal

Pin number

DCE DB-9
pin number

DCE DB-25
pin number

RXD

2

2

3

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Copyright © 2008 Nortel Networks

.

Содержание Passport 8600 Series





































































































































































Отзывы:

Нет отзывов