Nortel Passport 8600 Series Скачать руководство пользователя страница 143

Страница: 143 / 164

8692 SF/CPU module

143

To set up modem access, you need a DTE-to-DCE cable ( straight or
transmit cable) between the Modem port and a modem or terminal server.

The following table describes the required cable pin assignments.

Table 87
Pin assignments: DTE to DCE

Switch

Modem

Signal

Pin number

DCE DB-9
pin number

DCE DB-25
pin number

RXD

TXD

DTR

GND

DSR

RTS

CTS

8692 SF/CPU module

The following table describes the 8692 SF/CPU specifications.

Table 88
8692 SF/CPU specifications

Physical specifications

Height:

1.5 in. (3.8 cm)

Width:

15.4 in. (39.1 cm)

Depth:

18.5 in. (47.0 cm)

Weight:

7.2 lb (3.3 kg)

Electrical specifications

Input power:

100.6 W (142.5 W with SuperMezz)
maximum. See the following table.

Thermal rating:

343.0 (485.9) Btu/hr maximum

MTBF rating

213 454 hr

Connector types

Ethernet Management port:

RJ-45 connector wired as MDI (see

“8692 SF/CPU Management port”
(page 144)

)

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Содержание Passport 8600 Series
































































































































































Результаты поиска

Содержание Passport 8600 Series

Отзывы:

Nortel Passport 8600 Series, Руководство по установке, Страница: 143 / 164

Результаты поиска

Содержание Passport 8600 Series

Отзывы: