Nortel Passport 8600 Series Скачать руководство пользователя страница 135

Страница: 135 / 164

8683XLR module

135

Table 70
8648GTRS module specifications (cont’d.)

Electrical specifications

Performance specifications

Routing and switching forwarding
rates

8.5 Gbps

Cable specifications

Type:

Category 3, 4, or 5 for 10 Mbps
operation.

Category 5 or better UTP cable
for 100 Mbps and 1000 Mbps
operation. Cables must use all four
pairs. Wiring configuration and
performance are defined by EIA/TIA
Standard 568 and IEEE Standard
802.3 2000 edition.

Maximum distance:

328 ft (100 m)

The following table provides power specifications.

Table 71
8648GTRS power specifications

Specification

Value

3.3 V power (W)

71.6

12 V power (W)

136.8

Total power (W)

208.4

8683XLR module

The following table describes the 8683XLR module specifications.

Table 72
8683XLR module specifications

Physical specifications

Height:

1.5 in. (3.8 cm)

Width:

15.4 in. (39.1 cm)

Depth:

18.5 in. (47.0 cm)

Weight:

8.0 lb (3.6 kg)

Electrical specifications

Input power:

167.9 W maximum (includes XFPs).
See the following table.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Содержание Passport 8600 Series
































































































































































Результаты поиска

Содержание Passport 8600 Series

Отзывы:

Nortel Passport 8600 Series, Руководство по установке, Страница: 135 / 164

Результаты поиска

Содержание Passport 8600 Series

Отзывы: