Nortel Passport 8600 Series Скачать руководство пользователя страница 37

Страница: 37 / 164

Interface module descriptions

The following figure shows the location of the 8616GTE module LEDs.

Figure 9
8616GTE module LEDs

The following table describes the 8616GTE module LEDs.

Table 4
8616GTE module LEDs

Type

Label

Color, State

Meaning

Green, Steady

The port is linked and enabled.

Amber, Steady

The port is connected but detects an error
condition.

Link

Off

The port is disabled or has no link.

Port

Activity

Green, Blinking

The port is receiving data. As port utilization
increases, this LED can blink so fast that it
appears to be steady.

Green, Steady

The module has completed the power-on
self-test and software initialization and is
operating normally.

Amber, Steady

The module failed the power-on self-test.

Amber, Blinking

The module is inserted into the chassis and it
is running diagnostics.

Module

Online

Off

The module power is off. If the switch power
is on, the module is performing the power-on
self-test and software initialization. A module
in this state is not yet functional.

The 8616GTE module supports up to 32 000 table entries in its forwarding
engine.

The 8616GTE module does not support R or M mode.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Содержание Passport 8600 Series
































































































































































Результаты поиска

Содержание Passport 8600 Series

Отзывы:

Nortel Passport 8600 Series, Руководство по установке, Страница: 37 / 164

Результаты поиска

Содержание Passport 8600 Series

Отзывы: