manualshive.com logo in svg

Nortel Passport 8600 Series, Руководство по установке, Страница: 55 / 164

Поделиться
Скачать
Nortel Passport 8600 Series Скачать руководство пользователя страница 55

Interface module descriptions

55

Figure 26
8683XZR module

The 8683XZR module includes three forwarding engine lanes. Each lane
supports 10 Gbps bidirectional traffic. All three ports can run concurrently
at 10 Gbps.

The 8683XZR module is not supported in the 8003 chassis with Release
4.1 or later.

The 8683XZR modules support jumbo frames.

Nortel recommends that you install only one 10GBASE-ZR/ZW XFP in
one 8683XZR module due to cooling limitations on the 8683XLR and
XZR modules when using standard fan trays. Nortel further recommends
that you install the XFP only in Port 1. You can install a 10GBASE-SR,
-LR/LW, or ER/EW in one or both of the remaining ports.

There are no XFP limitations for this module in any slot when using the
new cooling modules for the 8010 and 8006 chassis.

The 8683XZR module supports up to three XFP transceivers. For a list of
Nortel-qualified XFPs for use in this module, see

“Nortel-qualified SFPs,

XFPs, and GBICs” (page 64)

.

The following figure shows the location of the 8683XZR module LEDs.

Figure 27
8683XZR module LEDs

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Copyright © 2008 Nortel Networks

.

Содержание Passport 8600 Series





































































































































































Отзывы:

Нет отзывов