Nortek Security & Control Mighty Mule MM371W Скачать руководство пользователя

Страница: 36 / 52

MM371W / MM372W Installation Instructions

LED1

LED2

LED3

TRANSMITTER PROGRAMMING

WARNING:

Changes, modifications or adjustments not expressly approved by Nortek Security and Control, LLC could void the user’s

authority to operate this equipment. There Are No User Serviceable Parts.

LED1

LED2

LED3

How to Learn a Transmitter:

1. On the control board, press and hold the (return/enter) button until LED2 beside the (return/enter) button turns on and the

buzzer sounds. Release the (return/enter) button.

2. Press and hold the desired transmitter button. Once learned, LED2 will flash and the buzzer will sound indicating that the

transmitter has been learned.

How to Erase a Transmitter or Keypad (MMK200) code:

Repeat steps 1-2 above to erase the learned transmitter or keypad code.

How to Erase ALL Learned Transmitters or Keypad codes:

1. Enter the 'Learn Transmitter' mode following step 1 above.
2. Press and hold the (down arrow) button until LED1, 2 & 3 flash and the buzzer sounds. (Approximately 10 seconds.)

Note:

The control board can store a total of 50 transmitter and/or keypad codes. The system is compatible with Mighty Mule DIP

switch transmitters and keypads.

Содержание Mighty Mule MM371W





















































Результаты поиска

Содержание Mighty Mule MM371W

Отзывы:

Похожие инструкции для Mighty Mule MM371W

Бренды по названию

Популярные бренды

Nortek Security & Control Mighty Mule MM371W, Руководство по установке

Результаты поиска

Содержание Mighty Mule MM371W

Отзывы:

Похожие инструкции для Mighty Mule MM371W

Бренды по названию

Популярные бренды