Nordmann Engineering Omega 12 Скачать руководство пользователя страница 87

Страница: 87 / 104

Warning

Fault

Message

Possible causes

Remedy

–––

E155

Ext. 5 V supply

External 5 V supply of the Nordmann Omega faulty. Voltage too

high or too low.

Note: The Condair Delta SPA Control Box or the Nordmann Ome-

ga, respectively continue to work normally.

Short circuit on LED.

Contact your Nordmann repre-

sentative.

Overload on LED connection.

Check LED connection.

E156

EEPROM read

Reading from EEPROM not possible.

Note: In order to reset the fault, the Condair Delta SPA Control

Box or the Nordmann Omega must be switched off and on again

(depending on which device the fault occurred).

EEPROM defective.

Contact your Nordmann repre-

sentative.

E157

EEPROM write

Writing to EEPROM not possible.

Note: In order to reset the fault, the Condair Delta SPA Control

Box or the Nordmann Omega must be switched off and on again

(depending on which device the fault occurred).

EEPROM defective.

Contact your Nordmann repre-

sentative.

–––

E158

Heat Element 1 control relay

Heating element control relay 1 does not work correctly.

Note: The operation of the Condair Delta SPA Control Box or

Nordmann Omega is stopped. After the fault has been eliminated,

the Nordmann Omega must be switched off and on again. If the

Nordmann Omega is controlled by a Condair Delta SPA Control

Box, the Condair Delta SPA Control Box must also be switched off

and on again after the Nordmann Omega has been restarted.

Heating element control relay 1

on control board blocked.

Contact your Nordmann repre-

sentative.

–––

E159

Heat Element 2 control relay

Heating element control relay 2 does not work correctly.

Note: The operation of the Condair Delta SPA Control Box or

Nordmann Omega is stopped. After the fault has been eliminated,

the Nordmann Omega must be switched off and on again. If the

Nordmann Omega is controlled by a Condair Delta SPA Control

Box, the Condair Delta SPA Control Box must also be switched off

and on again after the Nordmann Omega has been restarted.

Heating element control relay 2

on control board blocked.

Contact your Nordmann repre-

sentative.

–––

E160

Heat Element 3 control relay

Heating element control relay 3 does not work correctly.

Note: The operation of the Condair Delta SPA Control Box or

Nordmann Omega is stopped. After the fault has been eliminated,

the Nordmann Omega must be switched off and on again. If the

Nordmann Omega is controlled by a Condair Delta SPA Control

Box, the Condair Delta SPA Control Box must also be switched off

and on again after the Nordmann Omega has been restarted.

Heating element control relay 3

on control board blocked.

Contact your Nordmann repre-

sentative.

–––

E161

Heat Element 4 control relay

Heating element control relay 4 does not work correctly.

Note: The operation of the Condair Delta SPA Control Box or

Nordmann Omega is stopped. After the fault has been eliminated,

the Nordmann Omega must be switched off and on again. If the

Nordmann Omega is controlled by a Condair Delta SPA Control

Box, the Condair Delta SPA Control Box must also be switched off

and on again after the Nordmann Omega has been restarted.

Heating element control relay 4

on control board blocked.

Contact your Nordmann repre-

sentative.

Содержание Omega 12









































































































Результаты поиска

Содержание Omega 12

Отзывы:

Похожие инструкции для Omega 12

Бренды по названию

Популярные бренды

Nordmann Engineering Omega 12, Руководство по эксплуатации

Результаты поиска

Содержание Omega 12

Отзывы:

Похожие инструкции для Omega 12

Бренды по названию

Популярные бренды