Nordair Niche DH2 150 Скачать руководство пользователя страница 23

For two year operation, we recommend

that the following items should be held in

stock.

Should the heater be in constant 

operation, we suggest the following

items be stocked at all times.

We strongly recommend that your

heater be serviced twice a year, a

major service carried out prior to

heating season and a minor service

after 2000 running hours.

Nordair Niche must be consulted if 

genuine parts are not to be used.

Contact

Nordair Niche(A Division of AmbiRad)

6-14 Bean Leach Road

Hazel Grove

STOCKPORT

Cheshire

SK7 4LD

Tel: 0161 482 7900

Fax: 0161 482 7901

Description

Part No

Spark Probe 

N1014

Flame Probe IEG 18-6

N1007

Satronic MMI810

N1018

4 Pole Miniature Relays

N1244, N1260

Fenner Belts

See Technical Specification

Ignition Transformer

N1010

Duct Sensor 

See Wiring Diagram

Room Sensor

See Wiring Diagram

Description

Part No

Pilot Solenoid valve 

Refer to manufacturer

Main SSOV Actuator

Refer to manufacturer

Modulating Control Motor NM.24.SR

N9002

Overheat thermostat

N7042

Ambi-Tec controller

ATEM1

Ambi-Stat 1 Thermostat

AS1

(See wiring diagram)

Air Pressure Switch JD2

N3038

Motor MPCB

See Wiring Diagram

Control MCB 4 amp

N1157

Recommended spares

Содержание DH2 150



























Отзывы: