Nordair Niche DH2 150 Скачать руководство пользователя страница 11

Ensure gas valve motor rotational

switch to L (normal position).  Reset

active duct sensor temperature set

point to 40

˚

C adjust the span settings

to ensure the gas valve does not hunt

replace cover.

Tamper sealings

On completition of commissioning all

adjustable settings are to be sealed

with suitable evident seal.

Safety checks

With the burner firing, close burner 

isolating valve V6, lockout will occur.

Open valve and reset lockout

condition.

Remove the air sensing tube from the

bottom connection of the air pressure

switch.  The heater will lockout.

Replace and reset.  Adjust overheat

controller set point down until heater

shuts off on overheat.  Reset

temperature to 85

˚

C for the DV range

and 75

˚

C for the DH range. Reset by

depressing amber illuminated push

button on front of panel.

Instructions

On completition of commissioning the

engineer must instruct the end user

basic start up/shut down procedures.

Component

Limiting concentration

(CL) PPM (5 V/V)

Carbon

10

Carbon Dioxide

2500

(0.25)

Nitric Oxide

5

(0.0005)

Nitrogen Dioxide

1

(0.0001)

Aldehydes

0.4

(0.00004)

Содержание DH2 150



























Отзывы: