Nobles Speed Scrub Rider Скачать руководство пользователя страница 9

Страница: 9 / 54

OPERATION

SpeedScrub Rider 331140 (9- 2013)

HOW THE MACHINE WORKS

The scrub components of the machine are a

solution tank, scrub brushes or pads, a squeegee,

a vacuum fan, and a recovery tank.

The buttons on the control panel control the

machine scrubbing functions. The

One Step

Scrub button

turns the preset scrub functions on

and off. The FaST button (option) enables the

FaST (Foam Scrubbing Technology) system. The

ec- H2O

button (option) enables the

ec- H2O

(electrically converted water) system. The

vacuum fan / squeegee button

turns the vacuum

fan on/off and raises and lowers the squeegee.

The

brush pressure buttons

control the scrub

brush pressure, and the

solution buttons

control

the solution flow.

The

steering wheel

controls the path of the

machine travel. The

directional switch

controls the

forward or reverse direction of the machine. The

propel pedal controls the speed of the machine.

The

brake pedal

slows and stops the machine.

There are two different types of scrub heads

available, cylindrical and disk. Both scrub heads

are available in two different widths. The Disk

scrub head is available in 650 mm (26 in) wide and

800 mm (32 in) wide. The Cylindrical scrub head is

available in 700 mm (28 in) wide and 800 mm

(32 in) wide.

NOTE

The amount and type of soilage play an

important role in determining the type of brushes

or pads to use. For specific recommendations,

see the BRUSH INFORMATION section of this

manual or contact a Tennant representative.

CONVENTIONAL SCRUBBING

Water and detergent from the solution tank flow to

the floor through a solution valve. The brushes

use the detergent and water solution to scrub the

floor clean. As the machine propels forward, the

squeegee wipes the dirty solution from the floor.

The suction created by the vacuum fan then

draws the dirty solution from the squeegee into

the recovery tank.

FOAM SCRUBBING SYSTEM (FaST MODEL)

Unlike conventional scrubbing, the optional FaST

(Foam Scrubbing Technology) system operates

by injecting the FaST- PAK concentrate agent into

the system with a small amount of water and air.

This mixture creates a large volume of expanded

wet foam.

The expanded foam mixture is then dispersed

onto the floor while the machine is scrubbing.

When the squeegee picks up the mixture, the

patented foaming agent has collapsed and is

recovered into the recovery tank.

The FaST system can be used with all double

scrubbing and heavy duty scrubbing applications.

Using the FaST system improves safety and can

increase productivity by 30% by reducing your

dump/fill cycle. It will also reduce chemical usage

and storage space. One FaST- PAK of

concentrated agent can scrub up to 90,000 m

million square feet).

NOTE: Do not use the FaST system with

conventional cleaning detergents in the solution

tank. Drain, rinse and refill the solution tank with

clear cool water before operating the FaST

system. Conventional cleaning detergents may

cause failure to the FaST system.

Содержание Speed Scrub Rider























































Результаты поиска

Содержание Speed Scrub Rider

Отзывы:

Похожие инструкции для Speed Scrub Rider

Бренды по названию

Популярные бренды

Nobles Speed Scrub Rider, Руководство оператора

Результаты поиска

Содержание Speed Scrub Rider

Отзывы:

Похожие инструкции для Speed Scrub Rider

Бренды по названию

Популярные бренды