Nobles Speed Scrub Rider Скачать руководство пользователя страница 42

Страница: 42 / 54

MAINTENANCE

SpeedScrub Rider 331140 (03- 2015)

ec- H2O

SYSTEM (

ec- H2O

Model)

ec-H2O NanoClean WATER CONDITIONING

CARTRIDGE REPLACEMENT

(

ec-H2O models labeled ec-H2O NanoClean)

FOR SAFETY: Before leaving or servicing

machine, stop on level surface and turn off

machine.

The water conditioning cartridge is required to be

replaced when it reaches its maximum water

usage or expiration time of when the cartridge

was activated, which ever comes first. The

ec-H2O system indicator light will blink green/red

when it’s time to replace cartridge.
Depending on machine usage, on average, a new

cartridge can last anywhere from 12 months for

heavy machine usage to 24 months for light

machine usage.

ATTENTION:

During first time use and after

replacing the water conditioning cartridge, the

ec-H2O system will automatically override the

selected solution flow rate for up to 75 minutes.

1. Disconnect the wire harness from operator

seat and carefully remove seat from machine.

2. Remove the battery compartment shroud

from machine to access cartridge.

3. Disconnect the two hose connectors from

cartridge by pressing the gray collars inward

and pulling the connectors outward. Lift

cartridge to remove.

Gray Collar

4. Fill in the installation date on the new

cartridge label.

5. Install the new cartridge and reconnect the

two hoses. Make sure the hose connectors

are fully inserted into new cartridge.

6. Reset timer for new cartridge.

Carefully read and understand all steps first

before performing procedure.

a. Turn key on.

b. Press and hold the service switch, located

on the ec-H2O module, for 10 seconds.

After releasing service switch, the three

solution flow indicator lights will begin to

(ripple) move back and forth.

Within 5 seconds after releasing the service

switch, while the three indicator lights are

moving back and forth, quickly press and

release the solution flow button located on

ec-H2O module.

The three indicator lights will then blink three

times to indicate timer has been reset.

Repeat process if the three indicator lights

do not blink three times.

Service switch

3 indicator lights

Solution flow button

7. Reinstall the battery compartment shroud and

operator seat.

Содержание Speed Scrub Rider























































Результаты поиска

Содержание Speed Scrub Rider

Отзывы:

Похожие инструкции для Speed Scrub Rider

Бренды по названию

Популярные бренды

Nobles Speed Scrub Rider, Руководство оператора

Результаты поиска

Содержание Speed Scrub Rider

Отзывы:

Похожие инструкции для Speed Scrub Rider

Бренды по названию

Популярные бренды