Nobles Speed Scrub Rider Скачать руководство пользователя страница 18

Страница: 18 / 54

OPERATION

SpeedScrub Rider 331140 (03- 2015)

WATER PICKUP MODE (NO SCRUBBING)

The machine can be used to pick up water or

non- flammable liquid spills without scrubbing.

To pick up water or non- flammable liquid spills,

check to make sure that the

One Step Scrub

button

is not activated. The light next to the

One

Step Scrub button

must be off.

WARNING: Flammable materials or

reactive metals can cause an explosion

or fire. Do not pick up.

Then press the

vacuum fan button.

The light

above the

vacuum fan button

will turn on, the

squeegee will lower and the vacuum fan will start

operating. Then pick up the water or

non- flammable liquid spill.

WHILE OPERATING THE MACHINE

Drive as straight a path as possible. Avoid

bumping into posts or scraping the sides of the

machine. Overlap the scrub paths by several

centimeters (a few inches).

Avoid turning the steering wheel too sharply when

the machine is in motion. The machine is very

responsive to the movement of the steering wheel.

Avoid sudden turns, except in emergencies.

When scrubbing dead end aisles, start at the

closed end of the aisle and scrub out towards the

opening.

Adjust the machine speed, brush pressure, and

solution flow as required when scrubbing. Use the

minimal brush pressure and solution flow settings

as possible.

Keep the machine moving to prevent damaging

floor finishes.

If poor scrubbing performance is observed, stop

scrubbing and refer to

MACHINE

TROUBLESHOOTING

Conventional Scrubbing: Pour a recommended

foam control solution into the recovery tank if

excessive foam appears.

Change or rotate pads as necessary.

Observe the battery discharge indicator to ensure

there is adequate charge for machine operation.

Observe the solution tank indicator to ensure the

solution tank is not empty. Always empty recovery

tank before refilling the solution tank.

Observe the recovery tank indicator to ensure the

recovery is not full.

Remove the key when leaving the machine

unattended.

Perform the Daily Maintenance Procedures after

scrubbing (see MACHINE MAINTENANCE).

Drive the machine slowly on inclines. Use the

brake pedal to control machine speed on

descending inclines. Scrub with the machine up

inclines rather than down inclines.

FOR SAFETY: When using machine, go slowly

on inclines and slippery surfaces.

Содержание Speed Scrub Rider























































Результаты поиска

Содержание Speed Scrub Rider

Отзывы:

Похожие инструкции для Speed Scrub Rider

Бренды по названию

Популярные бренды

Nobles Speed Scrub Rider, Руководство оператора

Результаты поиска

Содержание Speed Scrub Rider

Отзывы:

Похожие инструкции для Speed Scrub Rider

Бренды по названию

Популярные бренды