Nobles Speed Scrub Rider Скачать руководство пользователя страница 30

Страница: 30 / 54

MAINTENANCE

SpeedScrub Rider 331140 (7- 2015)

BATTERIES

FOR SAFETY: Before leaving or servicing

machine, stop on level surface, turn off

machine, and remove key.

The lifetime of the batteries depends on their

proper maintenance. To get the most life from the

batteries;

Do not charge the batteries more than once a
day and only after running the machine for a
minimum of 15 minutes.

Do not leave the batteries partially discharged
for long period of time.

Only charge the batteries in a well-ventilated
area to prevent gas build up. Charge batteries
in areas with ambient temperatures 27

(80

F) or less.

Allow the charger to complete charging the
batteries before re-using the machine.

Maintain the proper electrolyte levels of flooded
(wet) batteries by checking levels weekly.

CHECKING THE ELECTROLYTE LEVEL

The flooded (wet) lead-acid batteries require

routine watering as described below. Check the

battery electrolyte level weekly.

NOTE:

Do Not

check the electrolyte level if the

machine is equipped with a battery watering

system.

08247

FOR SAFETY: When servicing machine, keep

all metal objects off batteries. Avoid contact

with battery acid.

The electrolyte level should be slightly above the

battery plates as shown before charging. Add

distilled water if low. DO NOT OVERFILL. The

electrolyte will expand and may overflow when

charging. After charging, distilled water can be

added up to about 3 mm (0.12 in) below the sight

tubes.

Before Charging

After Charging

NOTE: Make sure the battery caps are in place

while charging. There may be a sulfur smell after

charging batteries. This is normal.

MAINTENANCE-FREE BATTERIES

Maintenance-free (Sealed AGM) batteries do not

require watering. Cleaning and other routine

maintenance is still required.

CHECKING CONNECTIONS / CLEANING

After every 200 hours of use check for loose

battery connections and clean the surface of the

batteries, including terminals and cable clamps,

with a strong solution of baking soda and water.

Replace any worn or damaged wires. Do not

remove battery caps when cleaning batteries.

Содержание Speed Scrub Rider























































Результаты поиска

Содержание Speed Scrub Rider

Отзывы:

Похожие инструкции для Speed Scrub Rider

Бренды по названию

Популярные бренды

Nobles Speed Scrub Rider, Руководство оператора

Результаты поиска

Содержание Speed Scrub Rider

Отзывы:

Похожие инструкции для Speed Scrub Rider

Бренды по названию

Популярные бренды