Nitta NITTAOMEGA L Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 53

Nitta NITTAOMEGA L Скачать руководство пользователя страница 48

６

.Operations and Programming

40

Precautions for Operations

Do not separate the robot adaptor carelessly when the tool adaptor is not in
its home position on the tool stand.
Separating the tool adaptor while not in its home position may damage ATC
or peripheral equipment and/or hurt operators.

Basically, the connection surfaces of the robot adaptor and tool adaptor must
be in parallel during the ATC attaching/detaching operation.
Otherwise, proper chuck and smooth unchuck may be prevented. Moreover,
the electric contacts and hydraulic/pneumatic ports may be spoiled earlier.
If it is not possible to maintain parallelism with the robot and the tool stand,
the  tool  stand  must  have  an  alignment  function.  On  a  tool  stand  with  an
alignment function, mate the flat planes by pressing the robot adaptor against
the  tool  adaptor  for  proper  teaching.  (The  alignment  function  must  be
designed  to  compensate  for  robot  thrust,  tool  weight,  flatness,  and  center
deviation.)
Also, in the unchuck process, the tool adaptor may lean and cause prying due
to  reaction  force  of  ATC's  electric  contact  and  pneumatic  port,  preventing
unchuck. In such cases, the robot adaptor must be pressed against the tool
adaptor as in the coupling process to prevent the tool adaptor from moving
(deviating  and  leaning)  right  after  unchuck.  At  this  point,  the  tool  must
remain on the tool stand. Then, perform teaching so that the built-in sensors
can detect unchuck and ensure smooth evacuation without prying.
We have teaching jigs, so please feel free to contact us if you are interested.

Fig. 19. Precautions when teaching

For the above, it is recommended to place ATC's tool stand on the level.
However, if it needs to be upright due to a space constraint, please consider
the following.

1)

There must be no backlash of the tool adaptor's tool stand (besides the alignment function).

2)

It must not move due to tool's offset load during unchuck or chuck of the tool adaptor. (As far
as possible, it should be supported near the tool adaptor.)

3)

It must be pressed with sufficient pressure for coupling with the tool adaptor and have
sufficient rigidity to prevent deflection of the tool stand. Also the anchor bolts must not be
loosened or come off.

WARNING

CAUTION

Keep
parallel

NITTA

Teaching JIG

Robot side

AXM-R0006

Tool side

AXM-T0004

«
...
46
47
48
49
50
...
»

Содержание NITTAOMEGA L






















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды