manualshive.com logo in svg

Nitta NITTAOMEGA L, Инструкция по эксплуатации

Поделиться
Скачать
Nitta NITTAOMEGA L Скачать руководство пользователя страница 31

５

.Procedures of Installation to Robot/Tool 

23 

 

Connecting to Fitting/Removal Port 

Connect piping from the solenoid valve to the "CHUCK" port and "UNCHUCK" port of the 

fitting/removal mechanism. The constant pressure line (with the valve not energized) must 
always be connected with the "CHUCK" port to maintain coupling of the chuck/unchuck port 
in the event of power failure. 
 

  Be sure to shut off the power supply, air, water and hydraulic power before 

starting the work. 
 

●Be careful to ensure tubes are connected to right ports (chuck port (CH) and 

unchuck (UN) port). Otherwise the tool may fall off. 

●Clearly mark the chuck (CH) and unchuck (UN) tubes accordingly.

 

●Securely insert the tubes to the end to prevent accidental 

disconnection. 

●There are two types of chuck/unchuck air piping: standard spec and solenoid 

valve spec (a robot adaptor with solenoid valve). 

●For the solenoid valve spec, there are one air supply port.

 

●Do not manually switch the air supply without an abs

olute need to do so. 

     

 

           

Standard

                 

Solenoid valve spec 

 

 

Leave  the  "UNCHUCK"  port  opened  without  plugging  even  when 
chuck/unchuck is not to be performed (in a coupled state only). Also, be sure to 
pressurize the "CHUCK" port when using it. Otherwise, it may fall off. 

 

 

About air piping for ATC driving:   
ATC has a fail-safe mechanism to prevent the tool side from falling even when 
air  pressure  is  unexpectedly  decreased.  However,  the  air  piping  for  ATC 
driving requires proper selection and arrangement of solenoid valve to prevent 
air from flowing into the "unchuck" side even when the valve is electrically 
turned OFF. 

- Do not use any three-position, closed-center type solenoid valve. The chucked 

state cannot be maintained with the power supply turned OFF, which may 
result in falling. 

- Do not share an exhaust port with other equipment. Otherwise, the chucked 

state cannot be maintained due to wrap-around back pressure, which may 
result in falling. 

-  Do  not  branch  the  air  supply  to  the  "CHUCK"  port  to  other  equipment. 

Otherwise, the chucked state cannot be maintained due to reduced pressure, 
which may result in falling. 

 

 

 

WARNING

WARNING

DANGER

Single tube 
connection for 
solenoid valve spec 

Содержание NITTAOMEGA L






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды