Nilfisk-Advance SC530 53 BD GO Скачать руководство пользователя страница 27

Страница: 27 / 30

SC530 INSTRUCTIONS FOR USE

ENGLISH

DETERGENT TANK CLEANING

(For machines with Chemical Mixing System)
Clean the detergent tank (G, Figure. 24) as shown below:
1.

Drive the machine on a level floor.

Turn the ignition key (A) to "0".

Open the cover (B) and check that the recovery water tank (C)
is empty; if necessary empty it with the drain hose (D). Close
the cover (B).

Carefully lift the tank (C).

Unscrew the plug (E) and disconnect the hose (F) from the
tank (G).

Remove the tank.

Wash the tank in the appointed disposal area.

Install the tank (G) and connect the hose (F).

After draining the detergent tank, drain the Chemical Mixing
System too by running the system with clean water only.

MACHINE WORKING HOUR CHECK

Turn the ignition key (A, Figure. 25) to "I".

Press the switch (B), the hour meter (C) begins to work and it
at the same time shows the total number of working hours
(scrubbing/drying) performed by the machine.

Release the switch (B).

Turn the ignition key (A) to "0".

Figure 24

Figure 25

Содержание SC530 53 BD GO































Результаты поиска

Содержание SC530 53 BD GO

Отзывы:

Похожие инструкции для SC530 53 BD GO

Бренды по названию

Популярные бренды

Nilfisk-Advance SC530 53 BD GO, Инструкция по эксплуатации

Результаты поиска

Содержание SC530 53 BD GO

Отзывы:

Похожие инструкции для SC530 53 BD GO

Бренды по названию

Популярные бренды