Nilfisk-Advance SC530 53 BD GO Скачать руководство пользователя страница 28

Страница: 28 / 30

SC530 INSTRUCTIONS FOR USE

ENGLISH

FUSE CHECK/REPLACEMENT

Turn the ignition key (A, Figure. 26) to "0".

Disconnect the power supply cable (C, Figure. 26) from the
electrical mains.

Remove the screws (C .Figure27) on control panel (D), then
turn over the PCB to find the fuse (A, B, Figure 27).

Check/replace the following fuses:
A)

F1 fuse, low power circuit fuse:(5A)

F3 fuse, Brush release fuse: (20A)

Perform steps 1 to 3 in the reverse order.

Check/press down or replace the following breakers:
E)

F5breaker, vacuum motor circuit breaker: (30A)

F4 breaker, traction system circuit breaker: (12A) (*)

F2breaker, brush motor circuit breaker: (30A)

(*): Only for machine with traction

Figure 26

Figure 27

VACUUM TRACTION BRUSH

Содержание SC530 53 BD GO































Результаты поиска

Содержание SC530 53 BD GO

Отзывы:

Похожие инструкции для SC530 53 BD GO

Бренды по названию

Популярные бренды

Nilfisk-Advance SC530 53 BD GO, Инструкция по эксплуатации

Результаты поиска

Содержание SC530 53 BD GO

Отзывы:

Похожие инструкции для SC530 53 BD GO

Бренды по названию

Популярные бренды