Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.nightstick.com
INS-XPR-5572RM-17
9-19-2017
y
Use a hammer and a small center punch or nail to mark all 4 of the hole
locations through the template and then remove the tape and template.
y
If the charger is being installed onto drywall, you will need to install 4 -
#8 Drywall Anchors (included). Using a 1/4” drill bit, drill 4 holes through
the drywall in the locations of the nail marks. Using a #2 Phillips Head
Screwdriver, install all 4 Drywall Anchors into the drywall until they are each
flush with the surface.
NOTE: If the charger is being installed onto a metal surface, drill 4
appropriately sized holes. The diameter of the drill bit required will be
determined by the type of metal and the thickness of the material.
NOTE: If the charger is being installed onto a wooden surface, drill a
3/32” pilot hole in all 4 locations.
y
The mounting screw holes can be accessed from the front of the charger
when the Angle Light is not installed in the charger.
y
Looking through the mounting holes in the front face of the charger, line up
the mounting holes for the charger with the pilot holes (or drywall anchors)
and one at a time, carefully insert each of the supplied #8 x 32 x 1 ½” Pan
Head Screws into the mounting holes from the front of the charger. Give
each screw a small turn by hand to get each one started.
y
Using a #2 Phillips Head Screwdriver, hand-tighten each screw until the
charger is securely affixed to the mounting surface.
CAUTION:
Do not
use an electric drill or drill driver to install the screws. Do not over-tighten.
Doing so could damage the mounting holes in the charger.
y
Plug either the Nightstick AC or DC Power Supply cord into the power port
on the bottom of the 5572-CHGR1 charger and then into the appropriate
power outlet.
y
The LED Charge Indicator Light on the charger will momentarily light up
GREEN and then turn RED and then go off. This is normal behavior when
the Angle Light is NOT installed in the charger.
y
The charger is now ready to use.
POWERING THE XPR-5572RM
The XPR-5572R Intrinsically Safe Permissible Rechargeable Angle Light
can be powered in one of two ways:
y
The Nightstick 5572-BATT Lithium-ion Rechargeable Battery Pack.
y
The Nightstick 5570-BATT Non-Rechargeable Battery Carrier and 6 - AA
Energizer EN91
or
Energizer E91
Batteries.
WARNING: Do not use any other type of non-rechargeable battery with
this light.
WARNING: Do not use rechargeable AA batteries with this light.
5572-BATT LITHIUM-ION RECHARGEABLE BATTERY PACK
WARNING: The Nightstick 5572-BATT Lithium-ion Rechargeable Battery
Pack is a proprietary shape and design and will only fit in the XPP-
5570R or XPR-5572R Angle Lights. Do not attempt to use this battery
pack in any other light. Do not attempt to use any other rechargeable
battery pack in this light.
WARNING: The Nightstick 5572-BATT Lithium-ion Rechargeable Battery
Pack is a sealed unit and is not designed to be opened up. Do not
attempt to open the 5572-BATT Lithium-ion Rechargeable Battery Pack.
y
To install the 5572-BATT Lithium-ion Rechargeable Battery Pack, unscrew
the Torx Head Screw located on the Battery Compartment Door on the base
of the light using the included Torx Wrench. (Image 1)
NOTE: The Battery Compartment Door Torx Screw utilizes a design
that prevents the screw from falling out of the door. Do not attempt to
remove the screw. (Image 2)
y
With the Battery Compartment Door opened enough to provide clearance,
insert the 5572-BATT Lithium-ion Rechargeable Battery Pack with the end
having the metal contacts on it being inserted first and the rails on the
bottom of the Battery Pack positioned toward the back of the light. (Image 3)
y
With the 5572-BATT Lithium-ion Rechargeable
Battery Pack fully inserted into the handle of the
light, close the Battery Compartment Door and
secure it in place with the Battery Compartment
Door Torx Head Screw and the included Torx
Wrench. (Image 4)
WARNING: Do not over-tighten the Battery
Compartment Door Torx Head Screw.
The Angle Light is now ready to be powered
using the Nightstick 5572-BATT Lithium-ion
Rechargeable Battery Pack.
5570-BATT NON-RECHARGEABLE
BATTERY CARRIER
WARNING: The Nightstick 5570-BATT Non-Rechargeable Battery Carrier
is a proprietary shape and design and will only fit in the XPP-5570R or
XPR-5572R Angle Lights. Do not attempt to use this battery pack in any
other light. Do not attempt to use any other battery pack in this light.
The Nightstick 5570-BATT Non-Rechargeable Battery Carrier is designed
to fit 6 AA batteries. In order to maintain the XPR-5572R’s Intrinsically Safe
Permissible rating, the only AA batteries certified for use with this light are the
Energizer EN91
or
Energizer E91
.
Do not attempt to use any other brand or model of AA batteries with this
light.
Do not attempt to use any type of rechargeable AA batteries with this light.
Installing or replacing the batteries
y
Begin by positioning the 5570-BATT Non-Rechargeable Battery Carrier
with the arrow pointing to the left. (Image 5)
y
Using the thumb and index finger, squeeze in on the two sides of the
carrier cover closest to the right end of the carrier. (Image 6)
y
This action will cause the tabs on the right end of the cover to release from
the base and allow the cover to simply lift away. (Image 7)
y
Using 6 – AA
Energizer EN91
or
Energizer E91
(make sure that all 6
batteries are of one or the other model…do not use a combination of the
two), install the batteries per the diagram located on the inside base of the
battery carrier. (Image 8)
y
Take care not to bend any of the battery contact springs, and to make
sure that all 6 batteries are properly seated before reinstalling the cover.
(Image 9)
y
To reinstall the cover, insert the two tabs on the left-hand end of the cover
into the two corresponding slots on the left end of base. (Image 10)
y
While keeping the left-hand tabs in their slots, gently press down on the
right side of the cover until the two right-hand tabs slip into their respective
slots. (Image 11)
Image 1
Image 2
Image 3
Image 4
Image 5
Image 6
Image 7
Image 8
Image 9
Image 10
