Nice TITAN12L 912L Скачать руководство пользователя страница 21

Страница: 21 / 24

TITAN 912L Actuator

INSTALLATION REFERENCE MANUAL

1. Open mechanical release, remove two Torx 25 screws, and lift off cover (IMAGE 11-1).
2. Locate terminal strip per IMAGE 11-2.

3. Unscrew old wires from terminal strip, loosen strain relief, and pull out cable per IMAGE 11-3.

4. Insert new cable into strain relief per IMAGE 11-3 and strip each wire back 1/8” and twist.

5. Screw stripped colored cable wires into actuator terminal strip as shown in IMAGE 11-4.

Tighten strain relief, afix cover, close mechanical release, and lock.

ACTUATOR CABLE REPLACEMENT WIRING

IMAGE 11-1:

REMOVE COVER

IMAGE 11-3:

CABLE INSERTION

IMAGE 11-2:

LOCATE TERMINAL STRIP

IMAGE 11-4:

CABLE/TERMINAL STRIP WIRING

MECHANICAL

RELEASE (OPEN)

CABLE

STRAIN RELIEF

LIFT OFF COVER

TORX 25 TOOL

TERMINAL STRIP

LOCATION

WHITE

GREEN

ORANGE

YELLOW

BLUE

BLACK

RED

EXTEND LIMIT

COMMON

RETRACT LIMIT

ENCODER

MOTOR -

MOTOR +

SECTION 7: ACTUATOR CABLE REPLACEMENT WIRING

Содержание TITAN12L 912L

























Результаты поиска

Содержание TITAN12L 912L

Отзывы:

Похожие инструкции для TITAN12L 912L

Бренды по названию

Популярные бренды

Nice TITAN12L 912L, Инструкция по установке и справочное руководство

Результаты поиска

Содержание TITAN12L 912L

Отзывы:

Похожие инструкции для TITAN12L 912L

Бренды по названию

Популярные бренды