Nice MhouseKit WG2W, Инструкции и предупреждения по установке и использованию

Страница: 32 / 148

English
30 – English
TECHNICAL SPECIFICATIONS OF PRODUCT COMPONENTS
WG2W is manufactured by Nice S.p.a. (prov. of Treviso – Italy). In order to improve its products, Nice S.p.a. reserves the right to modify their technical
characteristics at any time without prior notice. In any case, the manufacturer guarantees their functionality and fitness for the intended purposes. Note:
all the technical characteristics refer to a temperature of 20°C.
CL2W command control unit
Type
Command control unit for 1 or 2 24Vdc motors for automation of automatic gates or doors, complete
with radio receiver for “GTX4” transmitters
Technology adopted
Electronic board governed by an 8 Bit microcontroller with flash technology. A transformer inside the
control unit, but separated from the board, reduces the mains voltage to the nominal 24V voltage used
in all of the automation system
Maximum cycles frequency 30 cycles/hour
Maximum continuous cycle time 230Vac (+10% -10%) 50/60Hz
Mains power supply
120W; at peak the power is 310W for a maximum duration of 2s
Nominal absorbed power Provision for “PR1” buffer battery connection
Emergency power supply
2, for 24Vdc motors with a nominal current of 1.1A, at peak power the maximum current is 3.5 A for
a maximum duration of 2 s
Motors output For normally open contacts (the closing of the contact causes the “OPEN” command)
Flasher output
For normally closed or normally open contacts and/or for constant resistance of 8.2 KΩ, or normally
closed contacts with self-recognition of the “normal” state (any variation from the memorised status
causes the “STOP” command)
ECSBus output 50 Ω for RG58 or similar type of cable
“OPEN” input
Mains power supply: 30m; motors outputs: 10m; other inputs/outputs: 20m with antenna cable pref-
erably shorter than 5m (observe the warnings regarding minimum gauge and type of cables)
“STOP” input -20 ÷ 50°C
Radio Antenna input
No
Maximum cable length Vertical, wall-mounted
Ambient operating temperature IP44
Use in acid, saline or potentially
explosive atmospheres
180 x 240 h 110mm / 2.8 kg
Mounting
Using “GTX4” transmitters, the control unit is able to receive one or more of the following commands:
“OPEN”, “Partial Open”, “Open Only” and “Close Only”
Protection rating Up to 256 if memorised in mode 1
Dimensions / weight
From 50 to 100m. This range can vary if there are obstacles or electromagnetic disturbances, and is
affected by the position of the receiving aerial incorporated in the flasher
Remote control compatibility
Using “GTX4” transmitters, the control unit is able to receive one or more of the following commands:
“OPEN”, “Partial Open”, “Open Only” and “Close Only”
Memorisable GTX4 transmitters
Up to 150 if memorised in mode 1
Range of the GTX4 transmitters
From 50 to 100m. This range can vary if there are obstacles or electromagnetic disturbances, and is
affected by the position of the receiving aerial incorporated in the flasher
Programmable functions
“Cycle” or “Complete cycle” (automatic closure) functionality
“Slow” or “fast” motors speed
Pause time during “complete cycle”, selectable from 10, 20, 40, 80 seconds
Partial opening type selectable in 4 modes
Obstacle detection system sensitivity, 4 selectable levels
“Open” command functionality selectable in 4 modes
Self-programming functions
Autodetection of Power&Free radio System devices from Mhouse
Recognition of the type of “STOP” device (NO or NC contact or 8.2 KΩ constant resistance)
Recognition of the manoeuvre length for each motor
Automation recognition with 1 or 2 motors
Radio protocol High security; compatible with the Power&Free System radio technology from Mhouse
Radio communication
Bidirectional, on 7 channels in band 868 MHz.
Installable wireless accessories Maximum 20 units
Installable PH100W photocells Maximum 6 pairs