background image

ENGLISH – 

21

8.3  CONNECTING THE PS324 BACK-UP BATTERY

The control unit is configured for being powered with PS324 back-

up batteries that intervene in case of a power outage.

Before installing a back-up battery, disconnect the 

power supply to the control unit.

Before installing and connecting the back-up battery:

1. 

remove the cover of the control unit’s containment box

2. 

insert the connector coming from the back-up battery into 

the slot (

A

) on the control unit

A

26

3. 

put the cover of the control unit’s containment box back on.

At this stage, the control unit can be powered again.

8.4  CONNECTING THE SOLEMYO SYSTEM

The control unit is configured for being powered with the “Solemyo” 

photovoltaic power system (photovoltaic panel and 24 V battery). 

To connect the Solemyo battery to the control unit, use the same 

connector (

A

) normally used for the back-up battery.

A

27

When the automation is powered through the 

“Solemyo” system, IT MUST NOT BE POWERED 

through the mains electricity at the same time.

The “Solemyo” system can only be used if the 

“Stand-by all” function is enabled (ON) on the 

control unit.

PRODUCT MAINTENANCE

9

 

PRODUCT MAINTENANCE

Being an electronic part, the control unit does not require any 

special maintenance. Nonetheless, the system should be 

regularly checked to ensure that it works efficiently at least every 

6 months according to the instructions in the “

TESTING AND 

COMMISSIONING

” chapter.

PRODUCT DISPOSAL

10

 

10 

PRODUCT DISPOSAL

This product is an integral part of the operator and 

must therefore be disposed of with it.

As with the installation, only qualified personnel must dismantle the 

product at the end of its life.

This product is composed of different types of materials. Some 

of these materials can be recycled; others must be disposed of. 

Please enquire about the recycling or disposal systems in place in 

your local area for this type of product.

WARNING
Some parts of the product may contain polluting or 

dangerous substances. If not disposed of correctly, 

these substances may have a damaging effect on 

the environment and human health.

As indicated by the symbol shown 

here, this product must not been 

disposed of with household 

waste. Separate the waste for 

disposal and recycling, following 

the methods stipulated by local 

regulations, or return the product 

to the seller when purchasing a 

new product.

WARNING
Local regulations may impose heavy penalties if 

this product is not disposed of in compliance with 

the law.

Содержание MC824HHS





























Отзывы: