NI DAQPad-MIO-16XE-50 Скачать руководство пользователя | Manualshive

Страница: 16 / 100

background image

Chapter 1

Introduction

DAQPad-MIO-16XE-50 User Manual

1-6

ni.com

Safety Information

The following section contains important safety information that you

must

follow during installation and use of the product.

Do

not

operate the product in a manner not specified in this document.

Misuse of the product can result in a hazard. You can compromise the
safety protection built into the product if the product is damaged in any
way. If the product is damaged, return it to NI for repair.

If the product is rated for use with hazardous voltages (>30 V

rms

, 42.4 V

pk

,

or 60 V

dc

), you may need to connect a safety earth-ground wire according

to the installation instructions. Refer to Appendix

Specifications

for

maximum voltage ratings.

Do

not

substitute parts or modify the product. Use the product only with

the chassis, modules, accessories, and cables specified in the installation
instructions. You

must

have all covers and filler panels installed during

operation of the product.

Do

not

operate the product in an explosive atmosphere or where there may

be flammable gases or fumes. Operate the product only at or below the
pollution degree stated in Appendix

Specifications

. Pollution is foreign

matter in a solid, liquid, or gaseous state that can produce a reduction of
dielectric strength or surface resistivity. The following is a description of
pollution degrees:

•

Pollution degree 1 means no pollution or only dry, nonconductive
pollution occurs. The pollution has no influence.

•

Pollution degree 2 means that only nonconductive pollution occurs in
most cases. Occasionally, however, a temporary conductivity caused
by condensation must be expected.

•

Pollution degree 3 means that conductive pollution occurs, or dry,
nonconductive pollution occurs, which becomes conductive due to
condensation.

Clean the product with a soft nonmetallic brush. The product

must

be

completely dry and free from contaminants before returning it to service.

You

must

insulate signal connections for the maximum voltage for which

the product is rated. Do

not

exceed the maximum ratings for the product.

Remove power from signal lines before connection to or disconnection
from the product.

«
...
14
15
16
17
18
...
»

Содержание DAQPad-MIO-16XE-50





































































































Отзывы:

Нет отзывов

Похожие инструкции для DAQPad-MIO-16XE-50

Бренд: QLA Страницы: 18

Бренд: Danfoss Страницы: 6

Бренд: Keithley Страницы: 201

Бренд: Magnum Energy Страницы: 3

Kotron 805 series

Бренд: Magnetrol Страницы: 36

Бренд: Magnescale Страницы: 104

Бренд: Magnescale Страницы: 44

Бренд: Olympus Страницы: 12

Бренд: Xantrex Страницы: 2

Бренд: Xaoc Devices Страницы: 8

Бренд: KALATEL Страницы: 38

Бренд: Fora Страницы: 64

Бренд: Elcontrol Страницы: 7

Бренд: Bühler technologies Страницы: 33

Бренд: Kinesys Страницы: 10

Бренд: REED Страницы: 20

Бренд: ICP DAS USA Страницы: 4

Бренд: G4M Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды