NFO Drives NFO 3A4D3490D, Руководство по эксплуатации и установке

Страница: 23 / 48


NFO Drives AB 2021 201013 ‐ 2 Operating and Installation Manual 23
USB bustype Select bus type/communication protocol for USB port Modbus RTU
NFO Classic
Modbus RTU
Modbus ASCII
Stby/Run
USB address Bus/station address 1 1 – 126 Stby/Run
USB timeout Set a communication timeout to stop motor or issue alarm [s] 0.0 0.0 – 10.0 Stby/Run
USB autostop Automatic stop motor if timeout is activated ON OFF / ON Stby/Run
ABCC interface Type of communication interface with ABCC module (internal) SPI Serial / SPI Stby/Run
ABCC bustype Shows the detected external fieldbus type - - Read
ABCC address ABCC module external network address (when applicable) 126 1 – 126 Stby/Run
ABCC timeout Set a communication timeout to stop motor or issue alarm [s] 0.0 0.0 – 10.0 Stby/Run
ABCC autostop Automatic stop motor if timeout is activated ON OFF / ON Stby/Run
Auto Reset
OFF : Changed setting of any communication parameter will not
be updated until after next power off – power on cycle.
ON : Auto update settings of communication device after
changing any communication parameter.
ON OFF / ON Stby/Run
Status
U-rms Motor voltage (RMS) V Read
I-rms Motor current (RMS) A Read
P-out Active power output W Read
PF Output power factor - Read
DC Link DC Link voltage V Read
Brake chop Voltage at brake chopper terminal V Read
Stator freq Electrical frequency (stator) actual value Hz Read
Rotor freq Electrical frequency (rotor) actual value Hz Read
Control freq Electrical frequency setpoint ( Frequency mode) Hz Read
Rotor speed Rotor speed actual value rpm Read
Control speed Rotor speed setpoint ( Speed mode) rpm Read
Actual torque Actual torque in percent of motor nominal torque % Read
Control torque Torque setpoint in percent of motor nominal torque [3] % Read
Actual PI-reg Actual value process regulator As per parameter Unit Read
Setpoint PI-reg Setpoint value process regulator As per parameter Unit Read
Analog 1 V Actual input voltage V Read
Analog 1 mA Actual input current mA Read
Analog 2 V Actual input voltage V Read
Analog 2 mA Actual input current mA Read
Keyboard Bitmask input of keyboard - Read
Terminals Bitmask input of terminals (DIN1..8) - Read
Temperature
Motor temp Estimated motor temperature in percent of max % Read
Power module Power module temperature [4] 
C
Read
COP temp Processor chip temperature [4]

C
Read
Heat sink 1 Heat sink temperature [4]

C Read
Heat sink 2 Heat sink temperature [4]

C Read
Heat sink 3 Heat sink temperature
[4] 
C Read
Heat sink 4 Heat sink temperature
[4] 
C Read
Fan volt 1 Cooling fan output voltage V Read
Fan volt 2 Cooling fan output voltage V Read
Fan volt 3 Cooling fan output voltage V Read
Fan volt 4 Cooling fan output voltage V Read
EXT 24V Actual voltage on external 24V supply V Read
USB 5V Actual voltage from USB connector V Read
Display
Display par 1
Selectable parameter for display left position: U
RMS
, I
RMS
, P
RMS
,
PF, U
DC
, Act.Freq, Act.Speed, Act.Torque, Act.Reg, TempMotor,
TempPower, TempHeatSink1-4, I[U]
RMS
, I[V]
RMS
, I[W]
RMS
,
I
RMS
several options Stby/Run
Display par 2 Selectable parameter for display middle position (same as par 1) P
RMS
several options Stby/Run
Display par 3 Selectable parameter for display right position (same as par 1) PF several options Stby/Run
Bklight level Illumination level for display 50% 10 – 100% Stby/Run
Bklight tmout Illumination dimmer timeout 2 min 0 – 60 min Stby/Run
Menu readonly
OFF : No activation of read only mode
ON : Activate readonly mode (require PIN code to deactivate)
OFF
OFF
ON
Stby/Run
Counters
Operating time Time that inverter has been powered on (hours x0.01) h Read
Run time Time that inverter has been running motor (hours x0.01) h Read
Brake time Time that inverter has activated brake chopper (seconds) s Read
Cur.limit time Time that inverter has been running in current limit (seconds) s Read
DC low time Time that inverter has activated brake chopper (seconds) s Read
Start counter Number of motor starts - Read
Alarm counter Number of logged alarms or faults - Read
Output energy Output energy to motor in kWh (resettable counter) kWh Read
Total energy Output energy to motor in MWh (non resettable counter) MWh Read
Version
COP version Firmware version of co-processor - Read
DSP version Firmware version of motor control processor - Read
3006469-2022-04