© 2021 Copyright Newmar Corporation. All rights reserved. For the most up-to-date version of this content, and for more product-specific information, please refer to Newgle.
99
ENTERTAINMENT SYSTEMS
Maintenance
The RoadTrip® P4 antenna is designed to be
maintenance free. However, it is a good idea to clean
the dome from time to time with a soft cloth, water, and
dish soap.
Source(s): Winegard RoadTrip P4 Automatic Stationary Roof-Mounted
Satellite TV Antenna
Product(s): Winegard RoadTrip Automatic Stationary Roof-Mounted
Satellite TV Antenna (Model: RTS-20B, Newmar Part Number: 135607)
DirecTV®
The RoadTrip® P4 antenna switch settings are preset for
DIRECTV. If you have a DISH or Bell TV receiver, you must
change the numbered switches found on the electronics
box under the dome.
RECEIVER SETUP
Connect the receiver to a power source, and complete
receiver setup. Check out online receiver setup guides for
your antenna at www.winegard.com/support.
RECEIVER RECOMMENDATIONS
The RoadTrip® P4 antenna will operate with most
DIRECTV receivers. Winegard does not recommend
using receivers with hard drives, as they are not intended
for mobile applications. Winegard does not recommend
using an HD receiver since HD programming will not be
available. SWM only receivers require a SWM-840 kit.
SATELLITE COVERAGE
The antenna will locate and toggle between satellites 101°
and 119°. The RoadTrip® P4 antenna will not operate in all
areas where satellites 101° and 119° are available. The P4
antenna is not compatible with 110° or KA-band satellites
99° and 103°. Satellite coverage maps are based on level,
stationary operation. Reception interruption may also
occur during adverse weather conditions.
Winegard Trav’ler Automatic Multi-Satellite TV Antenna
Operation (Models: SK-773, SKM-100, SWM-300)
This article provides basic operation instructions for a Winegard Trav’ler Automatic Multi-Satellite TV Antenna (Models:
SK-773, SKM-100, SWM-300).
Operation
The TRAV’LER antenna offers a simple one-button
operation. Simply press “POWER,” and the antenna
will automatically begin searching for satellites. The
instructions assume that the antenna is already in the
stowed position.
1. Press and hold “POWER” for two seconds or until the
TRAV’LER interface displays “POWER ON.”
2. Once the unit has been powered on, release
“POWER.”
3. The interface screen will display the type of satellite
dish on the top line.
4. The TRAV’LER antenna will enter the search mode
as part of its normal operation and will display
“Searching” on the bottom line.
5. The antenna will find its home position and begin
to look for a satellite. Upon finding a satellite, the
antenna will fine-tune or “peak” on the signal.
6. In automatic search mode, the TRAV’LER antenna
will lock onto multiple different satellites. The
antenna will display an asterisk for each satellite
found.
TIP: If you want to turn off the power to the TRAV’LER
antenna after the antenna has locked onto satellites,
press “POWER” and “SELECT” at the same time. Before
traveling, make sure to press “POWER” and wait for the
antenna to start to power up; then press “POWER” again
to initiate the stow sequence.
TRAV’LER SK-SWM3 SATELLITE
ANTENNA
•
DIRECTV Satellites: 99°, 101°, 103°
•
Views 3 Satellites Simultaneously
TRAV’LER SK-1000 SATELLITE
ANTENNA
•
DISH Satellites: 110°, 119°, 129° (61.5° Manual Only)
•
Views 3 Satellites Simultaneously
•
Bell TV Satellites: 82°, 91°
Содержание Bay Star 2022
Страница 1: ...SM 2022...