New Holland TC21D Скачать руководство пользователя страница 55

Страница: 55 / 102

SECTION 3 - LUBRICATION AND MAINTENANCE

3-4

WARNING

Fuel oil in the injection system is under high

pressure and can penetrate the skin. Unqualified

persons should not remove or attempt to adjust

a pump injector, nozzle, or any part of the fuel

injection system.

•

Do not use your hand to check for leaks. Use

a piece of cardboard or paper to search for

leaks.

•

If any fluid is injected into the skin, obtain

medical attention immediately or gangrene

may result.

Failure to follow these instructions can result in

serious injury.

Refueling the Tractor

The fuel tank filler cap, 1, is located at the right rear

corner of the tractor hood. Before removing the cap,

wipe all dust and dirt from around the cap to prevent

debris from falling into the tank while filling.

Use an approved fuel container and check the inside

of the container periodically for cleanliness. Fuel tank

capacity is 20L (5.3 gal).

NOTE:

The fuel cap is a vented-type. Use only an

approved New Holland replacement cap to prevent

fuel system-related problems.

If there is no filter on the storage tank or fuel

container, filter the fuel through a 100-mesh or finer

screen when filling the tractor fuel tank. Keep the

tractor tank as full as possible (without filling to

capacity) to minimize condensation.

NOTE:

It is a good practice to fill the fuel tank at the

end of each day, as this will reduce overnight

condensation.

19983660

NOT FOR REPRODUCTION

Содержание TC21D







































































































Результаты поиска

Содержание TC21D

Отзывы:

Похожие инструкции для TC21D

Бренды по названию

Популярные бренды

New Holland TC21D, Руководство оператора

Результаты поиска

Содержание TC21D

Отзывы:

Похожие инструкции для TC21D

Бренды по названию

Популярные бренды