New Holland TC21D Скачать руководство пользователя страница 30

Страница: 30 / 102

SECTION 2 - OPERATION

2-7

STARTING THE TRACTOR WITH

JUMPER CABLES

WARNING

Start the engine only from the operator’s seat. If

safety start switches are bypassed, the engine

can start with the transmission and/or PTO in

gear.

If you must use jumper cables to start the tractor:

1. Shield your eyes.
2. Connect one end of the jumper cable to the

tractor battery positive (+) terminal and the other

to the auxiliary battery positive (+) terminal. Next,

connect one end of the other jumper cable first to

the auxiliary battery negative (-) terminal, then

the other end to the tractor starter ground

terminal. Finally, start the tractor by following the

safe starting procedures outlined under “Starting

the Engine.” Idle the engine and turn on all

electrical equipment (lights, etc.), then discon-

nect the jumper cables in the reverse order in

which they were connected. This helps protect

the alternator from damage due to extreme load

changes.

WARNING

Batteries contain sulfuric acid and produce

explosive gases. To prevent personal injury:

••••

Wear eye and skin protection.

••••

Keep sparks and flame away.

••••

Ensure there is adequate ventilation while

charging or using the battery.

••••

Follow the manufacturer’s instructions

found on the battery.

STOPPING THE ENGINE

Turn the key switch to the “OFF” position to stop the

engine.

BREAK-IN PROCEDURES

Your New Holland tractor will provide long and

dependable service if given proper care during the

first 50-hour break-in period. During the first 50 hours

of operation:

1. Avoid “lugging” the engine. Operating in too high

a gear under heavy load may cause engine

lugging, which is indicated when the engine will

not respond to a throttle increase.

2. Use the lower gear ratios when pulling heavy

loads and avoid continuous operation at

constant engine speeds. You will save fuel and

minimize engine wear by selecting the correct

gear ratio for a particular operation. Operating

the tractor in low gear with a light load and high

engine speed wastes fuel.

3. Avoid prolonged operation at either high or low

engine speeds without a load on the engine.

4. Check the instruments frequently and keep the

radiator and oil reservoirs filled to recommended

levels. Daily checks include the engine oil level,

radiator coolant, and air cleaner.

5. After the first 50 hours of use, be sure to perform

the maintenance items listed in the maintenance

schedule.

NOT FOR REPRODUCTION

Содержание TC21D







































































































Результаты поиска

Содержание TC21D

Отзывы:

Похожие инструкции для TC21D

Бренды по названию

Популярные бренды

New Holland TC21D, Руководство оператора

Результаты поиска

Содержание TC21D

Отзывы:

Похожие инструкции для TC21D

Бренды по названию

Популярные бренды