New Holland E37C Скачать руководство пользователя страница 81

Страница: 81 / 296

3 - CONTROLS AND INSTRUMENTS

Angle blade version

The angle blade control lever is located on the right-hand
console.

The basic operation of angle blade control lever are the
following:

• push the angle blade control lever forward

(A)

to lower

the dozer blade

• pull the angle blade control lever rearward

(B)

to raise

the dozer blade

• move left-hand the slider to tilt the dozer blade leftward

(C)

(maximum angle:

25°

)

• move right-hand the slider to tilt the dozer blade right-

ward

(D)

(maximum angle:

25°

NOTICE:

never jack up or lift the machine with the angle

blade placed at an angle.

NOTICE:

stability of the machine is affected with blade at

angle, keep at neutral position.

NOTICE:

before start the working operations or traveling

up or down on a slope, position and keep the angle blade
at neutral position.

SMIL19MEX0454BB

SMIL18MEX0149AA

SMIL18MEX0130AA

3-23

Содержание E37C









































































































































































































































































































Результаты поиска

Содержание E37C

Отзывы:

Похожие инструкции для E37C

Бренды по названию

Популярные бренды

New Holland E37C, Оригинальное руководство пользователя

Результаты поиска

Содержание E37C

Отзывы:

Похожие инструкции для E37C

Бренды по названию

Популярные бренды