manualshive.com logo in svg

New Holland E37C, Оригинальное руководство пользователя

Original Instructions Manual для мини-экскаватора New Holland E37C теперь доступен для бесплатного скачивания на manualshive.com. Загрузите этот руководство, чтобы узнать всю необходимую информацию о вашем оборудовании. Будьте уверены, что вы всегда соблюдаете правила безопасности и эффективно используете ваш мини-экскаватор.

Поделиться
Скачать
background image

G

General specifications - Biodiesel fuels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-4

Grease points (Blade)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-20, 6-29

Grease points (Boom and arm)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-20, 6-42

Grease points (Bucket) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-20, 6-28

H

Handling the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-5

Hand signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
Hydraulic control lever operating pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
Hydraulic hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-62
Hydraulic oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-65
Hydraulic oil - breaker/auger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-26
Hydraulic oil level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-23
Hydraulic oil return filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-19, 6-52

Hydraulic oil suction filter

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-61

I

Injection nozzle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-54
Injection pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-62
Injection timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-62
Instrument cluster. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24
Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-2

K

Klac type buckets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9-3

L

Left-hand side controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Load handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-47
Loading the machine onto a transport trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-1

Lowering the attachment in the event of a failure . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-11

M

Machine components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
Machine orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-9

Machine specifications

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8-1

Machine travel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21
Maintenance chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-17

N

Note to the Owner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-1, 1-3

O

Operating the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-7

Operating the machine in hot or cold weather. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4-6

Operator's manual storage on the machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-8

Operator's seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-4

Other systems - Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7-3

P

Parking the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27
Periodic checks

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-78

Pilot line filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-19, 6-53

Plastic and resin parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-72
Preparing for storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-77
Product identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-5

Protecting the electronic and electrical systems during battery charging or welding . . . . . . . . . . . . 6-16

Q

Quick coupling system - Hydraulic pin-grabber type . . . . . . . . . . . . . . . . . . . . . . . . . . 9-39
Quick coupling system - Klac type

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-27

Quick coupling system - Mechanical pin-grabber type . . . . . . . . . . . . . . . . . . . . . . . . . 9-34

Содержание E37C









































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E37C

Case CX330 TIER III Manual preview
CX330 TIER III
Бренд: Case Страницы: 16
SANY SY16C Operation And Maintenance Manual preview
SY16C
Бренд: SANY Страницы: 208
Galeo PC16R-2 Operation & Maintenance Manual preview
PC16R-2
Бренд: Galeo Страницы: 31
achilles A14SE Owner'S Handbook Manual preview
A14SE
Бренд: achilles Страницы: 80
Case WX145 Operator'S Manual preview
WX145
Бренд: Case Страницы: 31
Case CX250C Service Manual preview
CX250C
Бренд: Case Страницы: 23
Case CX18C Service Manual preview
CX18C
Бренд: Case Страницы: 22
Case 9040B Troubleshooting Manual preview
9040B
Бренд: Case Страницы: 22
Case WX148 Service Manual preview
WX148
Бренд: Case Страницы: 51
Case CX17B Service Manual preview
CX17B
Бренд: Case Страницы: 41
Case CX210B Service Manual preview
CX210B
Бренд: Case Страницы: 51
Case CX800B Service Manual preview
CX800B
Бренд: Case Страницы: 61
Case CX260C Service Manual preview
CX260C
Бренд: Case Страницы: 61
Case CX210C Service Manual preview
CX210C
Бренд: Case Страницы: 81
Case CX160D Service Manual preview
CX160D
Бренд: Case Страницы: 81
Case 580 ck Operator'S Manual preview
580 ck
Бренд: Case Страницы: 74
Case CX135SR Operator'S Manual preview
CX135SR
Бренд: Case Страницы: 186
Case CX130 Manual preview
CX130
Бренд: Case Страницы: 262

Бренды по названию

Популярные бренды

Загрузить еще бренды