New Holland E37C Скачать руководство пользователя страница 118 | Manualshive

Страница: 118 / 296

background image

4 - OPERATING INSTRUCTIONS

Normal operation of the machine

When rolling in the arm, the roll-in movement stops mo-
mentary at point

(X)

as shown, then recovers speed again

after passing point

(X)

.

The reason is that the movement by the arm weight is
faster than the speed of oil flow into the cylinder. When
lowering the boom, a sound may be heard continuously.
This is caused by the oil flow in the valve.

If the machine is overloaded, a sound is caused by the
relief valves, which protect the hydraulic systems.

NOTICE:

do not exceed the machine performance. It may

result in accident or failure.

NOTICE:

perform lifting operations within the specified

load limit.

The upper-structure swings when the left control lever
is moved rightward or leftward. The swinging speed is
determined by the stroke of the lever.

• When moving the left control lever leftward, the upper-

structure swings leftward.

• When moving the left control lever rightward, the upper-

structure swings rightward.

• When returning the left control lever centrally (neutral

position) the upper-structure stops moving.

When you stop swinging the machine, a noise near the
swing motor may be heard. The noise is generated by
the brake valve.

NOTICE:

before start the work or when travelling up

or down a slope, position and keep the angle blade (if
equipped) at neutral position.

SMIL18MEX0131AB

1

4-8

«
...
116
117
118
119
120
...
»

Содержание E37C









































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E37C

Бренд: achilles Страницы: 28

Бренд: Takeuchi Страницы: 215

Бренд: jcb Страницы: 208

Бренд: Ravaglioli Страницы: 84

Бренд: RHINO Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды