New Holland E37C Скачать руководство пользователя страница 105

Страница: 105 / 296

3 - CONTROLS AND INSTRUMENTS

Opening

1. Use the starter key to unlock the engine door.

2. Use the hook to gently lift up the hood and use the

lifting stem

(1)

to secure the hood.

NOTICE:

while lifting the hood, make sure the hood does

not contact the cab. Machine damage could result.

NOTICE:

never leave tools inside the compartment.

SMIL16MEX1438AA

Closing

1. Lightly lift up the side hood, lower the lifting stem and

use the handle to lower the side hood gently.

NOTICE:

when you lower the hood, make sure that

the hood does not contact the cab. Machine damage
could result.

2. Make sure to close the side hood firmly.

3. Use the starter key to lock the hood.

SMIL16MEX1455AA

4. Pull the hook in order to unlock the engine access

door.

5. Use the handle and close the engine door firmly.

6. Use the starter key to lock the door.

SMIL16MEX1437AA

3-47

Содержание E37C









































































































































































































































































































Результаты поиска

Содержание E37C

Отзывы:

Похожие инструкции для E37C

Бренды по названию

Популярные бренды

New Holland E37C, Оригинальное руководство пользователя

Результаты поиска

Содержание E37C

Отзывы:

Похожие инструкции для E37C

Бренды по названию

Популярные бренды