New Holland E37C Скачать руководство пользователя страница 182

Страница: 182 / 296

6 - MAINTENANCE

Priming the fuel system

1. Turn the starter switch to ON position for

10 – 15 s

. The

electric fuel pump prime the fuel system.

NOTE:

never use the starter motor to crank the engine in

order to prime the fuel system. This may cause the starter
motor to overheat and damage the coils, the pinion and/or
the ring gear.

SMIL19MEX0717AA

Replace element

1. Rotate clockwise the fuel cock

(2)

located on the fuel-

water separator filter

(1)

to close the fuel flow.

2. Remove the cup

(4)

from the fuel-water separator filter.

3. Carefully hold the cup

(4)

to prevent fuel spilling. Clean

spilled fuel.

4. Remove the floating ring

(5)

from the cup.

5. Remove the filter element

(6)

, clean and replace if nec-

essary

6. Empty the cup

(4)

and rinse the inside with kerosene.

7. Install a new floating ring

(5)

in the cup

(4)

8. Tighten the cup

(4)

27.5 – 33.4 N·m

(

20.3 – 24.6 lb

9. Close the drain cock.

10. Rotate counterclockwise the fuel cock

(2)

to open the

fuel flow.

11. Prime the fuel system.

SMIL16MEX0601AA

12. Check for leaks.

6-36

Содержание E37C









































































































































































































































































































Результаты поиска

Содержание E37C

Отзывы:

Похожие инструкции для E37C

Бренды по названию

Популярные бренды

New Holland E37C, Оригинальное руководство пользователя

Результаты поиска

Содержание E37C

Отзывы:

Похожие инструкции для E37C

Бренды по названию

Популярные бренды