manualshive.com logo in svg

New Cosmos Electric NV-100H, Инструкция по эксплуатации, Страница: 32 / 43

Поделиться
Скачать
New Cosmos Electric NV-100H Скачать руководство пользователя страница 32

- 30 - 

⑥

Performance test using 

actual gas 

・

Apply the calibration gas to the gas detector and check if an alarm goes off.

・

Check that the ALARM lamp (red) on the indicator unit blinks and an alarm 

sound is given. (Refer to 8-3 for how to make calibration gas.) 

      How to apply calibration gas 

a. Diffusion type gas detector         b. Suction type gas detector

⑦

Visual inspection 

・

Check the following visually.

  ・

Clogging of the rainproof cap filter (diffusion type gas detector)

  ・

Clogging and corrosion of the frame arrester (diffusion type gas detector)

  ・

Corrosion of the gas detector

  ・

Corrosion of fittings 

⑧

Situation around the gas 

detector 

・

Check if there is anything blocking the diffusion or suction gas detector that is 

hindering the detection of gas. 

8-2  Maintenance inspections (Contact our dealer / agency for the inspection.) 

(1) Items to be inspected regularly and the inspection method 

Carry out the following inspections at least once a year. 

Table 2 

Items to be inspected 

Inspection method 

①

Sensor’s current 

inspection 

・

 Refer to “7-2. Procedures” (2). 

②

Zero point adjustment 

・

Refer to “7-2. Procedures” (3). 

③

POWER lamp check 

・

Refer to 2 on Table 1 about daily inspection. 

④

Preset alarm value 

・

Check that the preset alarm value mark on the indicator unit’s bar graph is at 

the proper value. (Refer to “7-2. Procedures” (4).) 

⑤

Flow inspection   

(Suction gas detector 
only) 

・

 Refer to 3 on Table 1 about daily inspection. 

⑥

Filter inspection 

(Suction gas detector 
only) 

・

Refer to User manual for Detector head 

⑦

Span adjustment 

(Sensitivity inspection) 

・

Apply calibration gas(1.6 times more than the preset alarm value) to the gas 

detector and check the bar graph on the indicator unit. 

⑧

Response time check 

・

 Check how long it takes from when you start applying gas to the gas detector 

until and an alarm goes off. It should be within 30 seconds.

*  If an alarm does not go off within 30 seconds, check for clogging of sintered 

metals or the filter of suction type gas detector. 

gas detector

calibration cap

gas bag

filter with   
a flow   
checker

gas bag

Содержание NV-100H












































Отзывы:

Нет отзывов