New Cosmos Electric NV-100H Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 43

New Cosmos Electric NV-100H Скачать руководство пользователя страница 24

- 22 -

⑦

Press the test button and simultaneously turn
the test volume until the reading matches the
peak hold value.

⑧

Then adjust the span adjustment volume
(SPAN) and adjust the indication value to the
calibration gas concentration.

⑨

Release the test button and confirm that the
indicated value indicates 1.0.

⑩

Press down the test button and adjust the
indication value to full scale.

⑪

Set the Mode switch at zero to return to normal
mode.

⑫

Apply the calibration gas and check to see if the
gas concentration is indicated correctly.

Match the peak
hold value.

POWER

ALARM

2

1

RESET

BZ STOP

POWER

ALARM

2

1

RESET

BZ STOP

Check to see if
the reading
returns to 1.0.

Return to the
Full scale.

POWER

ALARM

2

1

RESET

BZ STOP

POWER

ALARM

2

1

RESET

BZ STOP

Make sure that there is
no gas around the gas
detector and check to
see if the indicator
reads 1.0.

Note that a gas leak alarm and external output will be generated when calibration gas is applied in normal
mode.

CAUTION

BACK UP

POWER

ALARM

2

1

RESET

BZSTO

Scale for
calibration gas
concentration

BACK UP

BACK UP

BACK UP

POWER

ALARM

2

1

RESET

BZ STOP

Check the
calibration
concentration
reading.

BACK UP

BACK UP

«
...
22
23
24
25
26
...
»

Содержание NV-100H












































Отзывы:

Нет отзывов