Neumann.Berlin KH 150 Скачать руководство пользователя страница 5

KH 150 AES67  |  

5

Setting up and connecting the loudspeaker

CAUTION

Danger of injury and material damage due to tipping/dropping of the product!

If improperly mounted, the product and/or the mounting hardware (e .g . rack) can tip over 
or fall . 

 

X

Always have the product mounted by a qualified specialist according to local, national 
and international regulations and standards . 

 

X

Use the mounting systems recommended by Neumann and always provide sufficient 
additional protection against tipping or falling .

CAUTION

Damage to the product due to overheating!

If air cannot circulate properly around the cooling vents on the rear of the product, the 
amplifier(s) may overheat, leading to premature activation of the thermal protection sys-
tem which limits the maximum output level of the loudspeaker . In rare cases, damage to the 
product may also occur .

 

X

Never cover the cooling vents .

 

X

When installing the product into tight spaces such as wall recesses, maintain an air gap 
of at least 5 cm around the top, rear and side panels of the product and provide sufficient 
air circulation . If necessary, use forced-air cooling .

For further information on setting up loudspeakers, please refer to the “Questions & 
Answers” section on the product page at www .neumann .com .

For more information on building systems using Neumann loudspeaker products, please 
refer to the Product Selection Guide at www .neumann .com

Preparing the loudspeakers

CAUTION

Risk of staining surfaces!

Some surfaces treated with varnish, polish or synthetics may suffer from stains when they 
come into contact with other synthetics . Despite a thorough testing of the synthetics we 
use, we cannot rule out the possibility of staining .

 

X

Do not place the loudspeaker on delicate surfaces .

To place the loudspeaker on a flat surface:

 

X

Attach the supplied self-adhesive feet to the bottom of the cabinet .
This reduces the risk of scratching the surface and acoustically isolates the loudspeaker 
from the surface .

Preparing the room

 

X

Arrange all acoustically relevant surfaces and objects symmetrically on either side of the 
listening axis of the room (left/right) .

 

X

Minimize the sound that is reflected back to the listening position by using angled surfaces 
and/or acoustical treatment .

This product has been optimized for use in recording studios . In order to not affect the 
quality of playback, make sure that the product is used in an EMC (electromagnetically 
compatible) environment, ideally without electromagnetic radiation from other devices .

EN

Содержание KH 150






































Отзывы: