manualshive.com logo in svg

Neumann.Berlin KH 150, Инструкция по эксплуатации

Поделиться
Скачать
Neumann.Berlin KH 150 Скачать руководство пользователя страница 33

KH 150 AES67  |  

33

Compatibility with DANTE® AES67 audio streams

The loudspeaker can receive DANTE® AES67 audio streams .

Please refer to the user manual of your DANTE® interface or contact the manufacturer of 
your DANTE® interface to find out whether your DANTE® interface is capable of generating 
AES67-compatible streams . This feature must be implemented by the manufacturer of the 
DANTE® device .

To enable the DANTE AES67 SAP Protocol:

 

X

Navigate to the 

AES67 CONFIG

 menu item .

 

X

Select 

True

 from the 

Enable

 dropdown on the 

SAP Configuration

 tab .

This will enable the reception and discovery of AES67 streams generated by a DANTE® inter-
face . Routing (reception) of the stream can be done either with ANEMAN or via RX PATCH or 
RX STREAMS .

It is not possible to perform this configuration in the DANTE® controller software .

For more information on routing DANTE® AES67 streams with ANEMAN, refer to the doc-
umentation provided by Merging Technologies .

Routing DANTE® AES67 with RX PATCH

To establish a connection:

 

X

Open the loudspeaker’s web interface .

 

X

Navigate to the 

RX PATCH

 menu item in the menu on the left .

The top left will show all existing DANTE® AES67 audio sources (streams) in your network .

 

X

In the matrix, click on the cross point in the top left corner .
This will route all channels of the DANTE® AES67 stream to the internal DSP .
The matrix will indicate the routed audio with green cross points .
The audio will start playing .

To remove a connection:

 

X

Open the loudspeaker’s web interface .

 

X

Navigate to the 

RX PATCH

 menu item in the menu on the left .

The top left will show all existing DANTE® AES67 audio sources (streams) in your network .

 

X

In the matrix, click on the green cross point in the top left corner .
This will un-route all channels of the DANTE® AES67 stream from the internal DSP .
The audio will stop playing .

Routing DANTE® AES67 with RX STREAMS

To establish a connection:

 

X

Open the loudspeaker’s web interface .

 

X

Navigate to the 

RX STREAMS

 menu item in the menu on the left .

 

X

Click the 

 icon next to 

AES67 RX Streams

 .

The 

Advanced

 tab on the right will be enabled .

All discovered DANTE® AES67 sources will be shown in the 

Destination Name

 dropdown .

 

X

Select the desired DANTE® AES67 stream .

 

X

Enter a name for the stream .

 

X

Skip the 

Destination SDP

 box .

 

X

Highlight the first two lines in the 

Selected Channels

 box:

TDM.0 – I8S: #0

 and 

TDM.0 – I8S: #1

 

X

Click the downward arrow next to the 

Selected Channels

 box to enable these internal chan-

nels .

 

X

Leave the 

Link Offset

 box as it is .

 

X

Click 

Update Destination

 .

This will route all channels of the DANTE® AES67 stream to the internal DSP .

EN

Содержание KH 150






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды