Neumann.Berlin KH 150 Скачать руководство пользователя страница 19

Страница: 19 / 37

KH 150 AES67 |

Configuring AES67 network and audio settings

Initial setup

Before using the loudspeaker in your network, we recommend checking the AES67 network
settings and following this procedure for the initial setup of the AES67 interface .

The initial loudspeaker configuration and setup is divided into the following two procedures:
• The operational audio control mode: see the chapter “Selecting the control mode and audio

input” .

• AES67-compatible network interface: see the chapter “Setting up the AES67 network inter-

face” on page 20 .

Follow the steps described in these chapters in order to configure your AES67 network .

Selecting the control mode and audio input

The loudspeaker offers two different control modes to perform the audio configuration .

• In backplate mode (CONTROL = Local), all settings are performed via the controls on the

loudspeaker’s backplate .

• In network mode (CONTROL = Network), the controls on the backplate marked with “*” are

disabled . Settings can only be made using the

MA 1 – Automatic Monitor Alignment

soft-

ware .

For more information on the two loudspeaker control modes, refer to the chapter “CON-
TROL” on page 12 .

Setting the control mode for initial setup

Set the CONTROL switch to

Local

Keep it in this position during the initial AES67 setup .

Once the initial setup is done:

Set the CONTROL switch to

Network

in order to use the

MA 1 – Automatic Monitor Alignment

software for your individual room calibration .

For more information on the

MA 1 – Automatic Monitor Alignment

software, refer to:

https://en-de .neumann .com/ma-1

Setting the audio input mode for initial setup

Set the INPUT SELECT switch to AES67 in order to activate the AES67 audio and network
ports .

For more information on selecting the audio input signals, refer to the chapter “INPUT
SELECT” on page 12 .

*INPUT SELECT

GROUND LIFT

CONTROL

ANALOG

S/PDIF L

S/PDIF R

AES67

-3

*INPUT GAIN

[dB]

SETTINGS

Lift

Ground

Local

Network

*INPUT SELECT

GROUND LIFT

CONTROL

ANALOG

S/PDIF L

S/PDIF R

AES67

-3

*INPUT GAIN

[dB]

SETTINGS

Lift

Ground

Local

Network

*INPUT SELECT

GROUND LIFT

CONTROL

ANALOG

S/PDIF L

S/PDIF R

AES67

-3

*INPUT GAIN

[dB]

SETTINGS

Lift

Ground

Local

Network

Содержание KH 150






































Результаты поиска

Содержание KH 150

Отзывы:

Бренды по названию

Популярные бренды

Neumann.Berlin KH 150, Инструкция по эксплуатации

Результаты поиска

Содержание KH 150

Отзывы:

Бренды по названию

Популярные бренды